Linak DESKLINE DL12 User Manual
Hide thumbs
Also See for DESKLINE DL12:
- User manual (42 pages) ,
- User manual (40 pages) ,
- User manual (36 pages)
Subscribe to Our Youtube Channel
Related Manuals for Linak DESKLINE DL12
Summary of Contents for Linak DESKLINE DL12
- Page 1 DL12, DL14, DB14 and DL17 system with CBD4, CBD5 or CBD6 User manual LINAK.COM/DESKLINE Page 1 of 36...
-
Page 2: Table Of Contents
Initialisation of the DESKLINE parallel system ................. 21 Anti-Collision TM ........................... 22 PIEZO : description of the feature ..................23 Accessories and repair ......................... 24 Disposal of LINAK products ......................25 Labels ............................26 Drawing appendix ......................... 27 Declaration of conformity ......................34 Addresses ............................36... -
Page 3: Preface
This User Manual does not address the end-user. It is intended as a source of information for the manufacturer of the equipment or system only, and it will tell you how to install, use and maintain your LINAK electronics. It is the responsibility of the manufacturer of the end-use product to provide a User Manual where relevant safety information from this manual is passed on to the end-user. -
Page 4: Valid For
Valid for: This User Manual is valid for the following products: (See the first 3 - 5 characters on the label) Columns: DL12, DL14, DL17 Built-in actuators: DB14 Control boxes: CBD4, CBD5, CBD6 Controls: DP1U/DPF1M (if memory function is required), DP1C//DPT/DPF1C (if memory function and display are required) or DPA/DPB/DP1K/DP1V/DPFK (if only up/down is required) DPF1D (if display is required) -
Page 5: Important Information
Important information Important information on LINAK products can be found under the following ® headings: Warning! Failure to comply with these instructions may result in accidents involving serious personal injury. Failing to follow these instructions can result in the product being damaged or being destroyed. -
Page 6: Before Installation, Reinstallation Or Troubleshooting
• System connection. The individual parts must be connected before the control box is connected to the mains. See the User Manual for LINAK actuators, if necessary. During operation: • If the control box makes unusual noises or smells, switch off the mains voltage immediately. -
Page 7: Only For Eu Markets
Only for EU markets This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. -
Page 8: Repairs
Repairs In order to avoid the risk of malfunction, all DESKLINE repairs must only be carried out by authorised LINAK workshops or ® repairers, as special tools must be used and special gaskets must be fitted. Lifting units under warranty must also be returned to authorised LINAK workshops. -
Page 9: Misc. On The Deskline ® System
Misc. on the DESKLINE system ® Warranty - 60 months on DESKLINE (NEW) ® This will be valid for all DESKLINE products produced after the 1 of May 2015. ® Products produced before 1 of May 2015 will still be covered by 36 months. Products used in DESKLINE application: If these products are used in another application, they will be covered by 18 months warranty. -
Page 10: Description Of The Deskline ® System
Description of the DESKLINE system ® Each DESKLINE actuator/column is equipped with a motor and parallel/memory drive is ensured by means of software in the ® CBD4/CBD5/CBD6 that also takes account of an oblique load on the desk. Soft start and stop are also part of this software, which ensures a soft start and stop when adjusting the desk. -
Page 11: Mounting Guidelines For The Dl14 System
Mounting guidelines for the DL14 system Mounting top The top of the column is supplied with 4 M6 threaded holes meant for mounting onto the desk frame. We advise you to fasten the desk frame by means of 4 pcs. M6 screws of a good quality (min. 8.8) and of a suitable length, which must not go further than max. - Page 12 As the desktop amplifies the sound, we advise you to place a vibration/shock absorbing material between the desktop and the desk frame. (Example of how to mount a 2-parallel DESKLINE DL system) ® LINAK recommends that the DESKLINE DL system should be used in push applications. ® Page 12 of 36...
-
Page 13: Mounting Foot
Mounting guidelines for the DL14 system Mounting foot The DL14 is supplied with 4 M6 threaded holes and 2 M8 screws for mounting of the foot. You can either use 2 M8 screws or 4 M6 screws dependent on your foot design. We advise you to use screws of a good quality min. 8.8 and of a suitable length, which must not go further than 16 mm into the DL14 column. -
Page 14: Mounting Guidelines For The Dl12 System
Mounting guidelines for the DL12 system Mounting the top Mounting the feet The DL12 top plate is supplied with four M6 threaded The DL12 bottom plate is supplied with four M6 threaded holes. holes for mounting onto the top frame. 1. -
Page 15: Mounting Foot
MC 6 Mounting guidelines for the DL17 system Mounting top Mounting foot The top of the column is supplied with 4 x M6 threaded The DL17 is supplied with 4 x M6 threaded holes and 2 x holes meant for mounting onto the desk frame . We advise M8 screws for mounting of the foot. - Page 16 When mounting the DL17 to the tabletop and feet, we recommend orienting the column, so the cable is pointing in direction of the centre of the desk. Page 16 of 36...
-
Page 17: Mounting Guidelines For The Db14
Motor Middle tube: For detailed information on how to mount the middle tube of your column, please contact LINAK A/S Bottom: At the bottom of the DB12 or the DB14 the inner spindle should be mounted by means of a 22-teeth spline profile and a M5 screw in the bottom of the spindle. - Page 18 For detailed information on how to mount the DB14, please contact LINAK A/S. From the factory, the DB14 is delivered with the hollow spindle driven into end position. Please observe that the solid spindle may roll out during transportation/handling, but it must be rolled back to end position before mounting in the profile.
-
Page 19: Mounting Guidelines For The Cbd4/Cbd5/Cbd6
Mounting guidelines CBD4/CBD5/CBD6 The control box is to be fastened with 4 screws (3 screws for the CBD5 and theCBD6) with a head diameter between ø 8 and ø 10 mm. Out of regard for the surface tension ø 10 mm is preferable due to lower surface tension. See drawing appendix for placing of mounting holes and the space the CBD takes up. -
Page 20: Electrical Connection Of The Db/Dl System
The function of the earth cable is to earth the desk and ground static electricity. The earth connection does not protect other electrical products. CBD4/CBD5 with mains cut-off (non ZERO models) If the power cable is damaged it has to be replaced by an authorized LINAK service centre to avoid any danger. Hook for cable relief Mains cable... -
Page 21: Initialisation Of The Deskline Parallel System
Initialisation of the DESKLINE parallel system The DESKLINE system is initialised by pressing the down button once or twice and holding it down until the DB/DL runs into end stop. It will then automatically run approx. 5 mm out again and hereafter slowly run in again. Only release the down button when the movement has stopped completely. -
Page 22: Anti-Collision Tm
Anti-Collision™ The function (anti-collision) is an option for the standard CBD4/CBD5/CBD6 advanced/control box software 0077432 version 1.66 and later. A system with anti-collision can limit material damages on a desk if a collision with a solid object should occur. Enabling the anti-collision To enable the anti-collision function a little plug called a dongle must be mounted in one of the 2 control ports. -
Page 23: Piezo Tm : Description Of The Feature
PIEZO™: description of the feature For optimised safety against squeezing and blocking on a desk, LINAK has developed the DESKLIFT columns with an integrated sensor, called PIEZO. The option minimises the risk for damages on a desk caused by squeezing or blocking of obstacles in up and down direction. -
Page 24: Accessories And Repair
Accessories Please contact your nearest LINAK dealer for information. Repairs Systems should only be repaired by an authorised LINAK service centre or an engineer. Systems to be repaired under warranty must be sent to an authorised LINAK service centre. Warning! By unauthorised opening of the system there is a risk that it may malfunction at a later date. -
Page 25: Disposal Of Linak Products
Disposal of LINAK products As LINAK customers often ask us how our products can be disposed of or scrapped, we have prepared this guidance that enables a classification to different waste fractions for recycling or combustion. Guidance We recommend that our products be disassembled as much as possible and divided into different waste groups for recycling or combustion. -
Page 26: Labels
Labels Label for DL12 Label for DL17 Label for DB14 Label for DL14 Label for CBD6 Label for CBD4 Label for CBD5 Page 26 of 36... -
Page 27: Drawing Appendix
DRAWING APPENDIX DL12 Page 27 of 36... - Page 28 DL12XL extended version Page 28 of 36...
- Page 29 DL12 with motor housing Page 29 of 36...
- Page 30 DL14 Page 30 of 36...
- Page 31 DL17 ng No.: 0639080 ng No.: 0639080 +6.5 1178 -4.5 518 3.5 Page 31 of 36...
- Page 32 Drawing No.: DB14_NEW_MOTOR Drawing No.: DB14_NEW_MOTOR DB14 Nominal length 508 3mm Minimum length retracted at max. load 503 12.73 CBD4 Page 32 of 36...
- Page 33 CBD5 CBD6 Page 33 of 36...
-
Page 34: Declaration Of Conformity
LINAK APPLICATION POLICY The purpose of the application policy is to define areas of responsibilities in relation to applying a LINAK product defined as hardware, software, technical advice, etc. related to an existing or a new customer application. LINAK products as defined above are applicable for a wide range of applications within the Medical, Furniture, Desk and Industry areas. - Page 35 Page 35 of 36...
-
Page 36: Addresses
The user is responsible for determining the suitabil- Fax: +86 755 8610 6990 Tel: +64 9580 2071 ity of LINAK products for a specific application. All sales are subject to the ‘Standard Terms of Sale and Fax: +64 9580 2072 www.linak.cn...
Need help?
Do you have a question about the DESKLINE DL12 and is the answer not in the manual?
Questions and answers