Table of Contents
Advertisement
Pandora Alarm Studio
The Pandora Alarm Studio allows you to change the main settings and parameters of the system,
update firmware, download installation manuals, connect to the server to make CLONE procedure. A
current version of the Pandora Alarm Studio can be downloaded from pandorainfo.com. The Pandora
Alarm Studio is provided only to authorized installers of Pandora systems.
• Download the Pandora AlarmStudio to a PC with Windows XP/Vista/7/8/10.
• Run the Pandora AlarmStudio;
• Connect the system to the PC via a USB cable;
• Put the system to the programming mode;
• The Pandora AlarmStudio will automatically connect to the system and you will be able to configure
settings and update firmware.
Updating firmware
It is recommended to update firmware of the base unit before installing and programming the
system. You can update firmware using the Alarm Studio application after entering programming mode
or using quick boot algorithm (the PIN-code is not required).
Quick boot mode: open the Alarm Studio; de-energize and disconnect the system; press and hold
the VALET button located on the base unit; release the button immediately after connecting the system
to a computer via USB cable; the system will enter boot mode.
!
i
f ThE bOOT mOdE has bEEN iNTErrupTEd fOr sOmE rEasON aNd ThE sTaTus iNdicaTOr lighTs rEd
(
firmwarE usiNg quick bOOT mOdE
wiThOuT ENTEriNg ThE
Pandora Specialist application
The Pandora Specialist mobile application (Android only) is available for
system configuration:
• Download and install the Pandora Specialist mobile app (scan the QR-
code or go to the Google Play app store);
• Connect the USB-OTG adapter to your smartphone or tablet;
• Connect the USB cable to the system;
• Connect the USB-OTG adapter to the USB cable;
• Enter the «Service PIN».
52
,
yOu NEEd TO lOad
piN-
).
cOdE
PA N D O R A L I G H T V 3
Programming using the VALET button
The system allows programming some settings using the VALET button. To configure all settings use
Pandora Alarm Studio program and Pandora Specialist application.
Enter the programming mode by entering the «Service PIN-code», use the VALET button to enter the
desired level number (press the button a number of times, equals to the level number; pauses between
presses should not exceed 1 second). The system will confirm correct input with red LED flashes and short
sound signals of a siren and proceed to the desired level. If the input was incorrect, the system will not
confirm input and will await a new level input after a series of green and red flashes.
For quick access to the higher level, press and hold the VALET button. The siren will sounds tone
beeps (up to 10). These sounds means the sequence number of a two-digit level number (the first signal
– level №10, the third signal – level №30, the tenth signal – exit programming menu). Release the VALET
button immediately after the desired number of signal. To enter an intermediate level, press the
VALET button the number of times equals to the second digit of the desired level number immediately
after releasing the button. The system will confirm correct input with red LED flashes and short sound
signals of the siren/beeper and proceed to the desired level.
PROGRAMMING TABLE
Level 1
Recording remote controls (D-010, DXL-707/078/077, R-387) 4 pcs.
Level 2
Changing the factory preset of the «Service PIN-code»
Level 3
Recording the idle speed to the system memory
Level 4
Resetting to factory settings
Level 11
Programming and configuring the «Immobiliser code»
Level 12
Fuel level calibration
Level 13
Emergency control of the code immobiliser
Level 17
Programming bypass of original immobiliser
Level 30
Programming the «Beach mode PIN-code»
U S E R A N D I N S TA L L AT I O N M A N UA L
53
Advertisement
Table of Contents
