Table of Contents
Advertisement
Pandora
model:
When implementing a bypass procedure using IMMO-KEY port it is
necessary to disable any logic on INP1 and INP7 (default logic for
INP1 - «Trunk switch»).
3
Black
IMMO-KEY2
2
IMMO-KEY1 IN
White
IMMO-KEY1
1
Green
«Trunk switch»
LED/CAN
VALET
External VALET button
X7
X6
X5
X4
X1
X3
X2
Analog temperature sensor
micro-USB
WARNING!
IT IS FORBIDDEN
The main unit is designed to operate
the place where temperature is higher than the
at temperatures from -40°C to +85°C, the degree
operating range of the sensor (+125°C) and cable
of protections is IP40.
(+80°C).
WARNING!
distance of 20mm from metal parts)
X3 X1
X4
X5
X6 X7
32
LIGHT v3
WARNING!
Before starting the installation of the
system: check the connection points on
loader.pandorainfo.com, Pandora Specialist, Pandora
Alarm Studio, update system rmware, choose a car
model if connecting to CAN-bus.
Red
OUT/INP7
Brown
3
6
OUT/INP1
Yellow
2
5
Orange
1
4
Green
Blue
LED
16
8
VALET
15
7
6
14
5
4
12
2
LIN-Input
Black
11
3
LIN-Output
1
White
2
10
9
1
to install the temperature sensor at
Do not shield the built-in antenna (Keep minimum
X2
R20
PA N D O R A L I G H T V 3
WARNING!
The base unit and system elements must be
installed in places with appropriate temperature, moisture
and dust protection characteristics (IP40 - interior, IP54 and
higher - interior, engine compartment).
WARNING!
All power circuits of additional devices that are
not powered through the base unit of the system should
have their own fuses.
+ 12V
«Ignition»/
CH9
«Button»*
+12B
200mA (-)
CH10 «Starter»
200mA (-)
«
»/
CH6
200mA (-)
«Brake pedal»*
200mA (-)
200mA (-)
CH8 «Bypass»
* For remote start implementation by Start/Stop algorithm
CH7 «Blocking NO»
Red
2 (+)
Purple
(+)
Yellow
200mA (-)
Blue/Black
150mA (-)
Yellow/Black
Orange/Black
(-)
Brown/White
(-)
Blue
Black
(+)
Blue/White
200 mA (-)
Green
(-)
Grey
150mA (-)
Yellow/White
Orange/White
(-) 200mA
Red/Black
U S E R A N D I N S TA L L AT I O N M A N UA L
(Uamp3...100V, min 8Hz)
White
WARNING!
The security system is a maintenance-free
device. In case of failure you must immediately
contact local specialized service center.
IT IS FORBIDDEN
normal voltage other than 12V.
IT IS FORBIDDEN
damaged output cables.
IT IS FORBIDDEN
of the fuses provided with the security system when
connecting to the vehicle's wiring.
Relay module
IP54
(scheme is
on the next page)
POWER SUPPLY (+12V)
CH11 – «Siren» (+12V)
INP6 – «Ignition input»
CH1 – «Beeper output»
INP3 – «Front hood switch»
INP4 – «Neutral/Handbrake input»
GROUND
– «Brake pedal»
/«Fuel level input»
INP5
– «Turn indicators»
CH3
INP2 – «Doors switch»
CH5 – «Open trunk» output
«Tachometer input»
to install the system on a car with
to install the security system with
to exclude or change the nominal
CAN2-H/CH4
CAN2-L/CH2
CAN1-H
CAN1-L
33
Advertisement
Table of Contents
