General Parameter Table - Siruba C007K Manual

6. General Parameter Table :

Parameter
Mode
Code
001. H Maximum sewing speed
Start Back-Tacking speed or
004. N Constant-Stitch speed for the
Interlock Stitch machine
005. V
End Back-Tacking speed ( spm )
006. B
Bar-Tacking speed ( spm )
007. S
Slow Start speed ( spm )
008. S L S Number of Stitches for the Slow Start
Automatic Constant-Stitch sewing
speed or Auto-start testing speed
009. A
( spm )
A
Automatic End Back-Tacking sewing
010. A C D
(Can invalidate the Stitch Correction function)
011. RVM
Back-Tacking Mode selection
040. W O N
Wiper function selection
041. T M Trimmer function selection
045. S P
Sewing speed
046. D I R
Direction of motor rotation
060. L Low speed ( spm )
061. T Trimmer speed ( spm )
Full-On time setting for Automatic
064. F O
Foot Lifter ( ms )
Duty-Cycle setting for Automatic
065. F C
Foot Lifter ( ％ )
066. F D Running-Delay time setting (ms )
Cancel Automatic Foot Lifting when
070. H H C
B
Half-Heeling the pedal
075. S F M
Safety switch mode
083. T 2
Trimming timing (ms)
087. L 2
Tension release timing (ms)
093. W 2 Wiper timing (ms)
119. DD
Motor drive mode
Needle goes up automatically as
121. A N U
power turned on
122. HL
Upper limit of maximum speed
Parameter Function
( spm )
( spm )
Range /
Selection
50 ～ 9999
Maximum speed adjustments.
Speed adjustment for Start Back-Tacking or Constant-Stitch
50 ～ 8000
sewing in the Interlock Stitch machine.
50 ～ 8000
Speed adjustment for End Back-Tacking.
50 ～ 8000
Speed adjustment for Bar-Tacking.
50 ～ 2000
Speed adjustment for Slow Start.
0 ～ 99
Number of Stitches setting for Slow Start.
Speed adjustment for Automatic Constant-Stitch sewing.
50 ～ 8000
Note：Valid only when the【 037. SMP】 set on 『A 』
O N：After last seam of Constant-Stitch sewing, it will automatic
execute the End Back-Tacking sewing function.
Note：When turned on, the Stitch-Correction is invalid.
ON / OFF
OFF：Automatic End Back-Tacking will not execute after last seam,
but can be done by pedal manually
Note：The Stitch-Correction is valid in Free sewing, but the
J ：JUKI mode ( Press TB switch will activate the reverse solenoid
when either machine is stopped or running).
J / B
B：BROTHER mode (Press TB switch will activate the reverse
solenoid only when machine is running).
O N ：Wiper valid.
ON / OFF
OFF：Wiper invalid.
O N：Trimmer valid.
ON / OFF
OFF：Trimmer invalid.
0~8000 Showing the current sewing speed.
C W ：Clockwise.
CW / CCW
CCW：Counterclockwise.
50 ～ 500
Speed adjustment for Low speed.
50 ～ 500
Speed adjustment for Trimmer.
0 ～ 990
Timing adjustment for Full-On time of Automatic Foot Lifter actives.
Adjustment for Duty-Cycle of AFL.
10 ～ 90
(Fine tuning can reduce the over heating)
0 ～ 990
Running-Delay time adjustment for the Automatic Foot Lifter.
O N ：Pedal half heeling without foot lifting function.
(Only full heeling can activate Foot Lifer.)
ON / OFF
OFF：Pedal half heeling with foot lifting function.
NO：Means Normal Opened.
NC / NO
NC：Means Normal Closed.
0 ～ 990
Adjustment for trimming timing
0 ～ 1500
Adjustment for tension release timing.
0 ～ 9990
Adjustment for wiper timing.
O N：Motor drive machine head directly
ON / OFF
OFF：Motor drive machine head with belt.
O N：Power turned on, needle goes up position automatically.
ON / OFF
OFF：No Use.
50 - 9999 The motor's maximum speed setting.
15
Description / Note
parameter 【011.RVM】 must set on『 B 』.