Hytronik DualSense HIM11 Installation And Instruction Manual

SURFACE MOUNT DUAL SENSE MOTION SENSOR HIM11
1. Technical Specifications
Product type Dual sense motion sensor ( HF and PIR, Tri-level control )
Operating voltage 120~277VAC 50/60Hz
Rated load Capacitive: 400VA@120V; 800VA@220~277V
Resistive: 700W@120V; 1600W@220~277V
Power consumption < 1W
o
Detection angle 360
Installation Height : 6m
Detection area (Max.)*
Detection Range (Ø) :12m
Detection range 10% / 50% / 75% / 100%
Hold time 2s / 30s / 1min / 5min / 10min / 15min / 20min / 30min
Stand-by time 0s / 10s / 1min / 5min / 10min / 30min / 1h / +∞
Stand-by dimming level 10% / 20% / 30% / 50%
Daylight threshold 2 ~ 500Lux, Disable
Warmming up time 30s
o
Operating temperature -20 C ~ +55
Sensor mode PIR, HF, PIR+HF, PIR / HF

3. Rotary Switch Settings

A rotary switch is built inside the sensor for
scene selection / fast programming. Total
16 channels available:
Detection Hold
Channel
range time
0 100% 5s
1 100% 1min
2 100% 5min
3 100% 5min
4 100% 5min
5 100% 5min
6 100% 5min
7 100% 10min
8 100% 10min
9 100% 10min
A 100% 10min
B 75% 10min
C 50% 10min
D 100% 30min
E 100% 30min
F 100% 5s
Note: settings can also be changed by remote control HRC-11. The last action controls.

4. Sensor Mode Selection

Sensor mode can be easily selected by choosing the correct combination of the DIP switches
(see table below):
1 2
I
II
III
IV
Installation and Instruction Manual
o
C
Rotary switch preset (Please
see the location in 2. Installation)
Stand-by Stand-by
time dimming level
10s 10%
5min 10%
10min 10%
30min 10%
0s Disable
+∞ 10%
+∞ 30%
10min 10%
30min 10%
+∞ 10%
+∞ 30%
+∞ 10%
+∞ 10%
+∞ 10%
+∞ 30%
10s 10%
HF+PIR: Light is on when both HF
and PIR sensors are activated.
HF
PIR
HF/PIR: Light is on when HF or PIR
HF+PIR
sensors are activated.
HF/PIR

2. Installation

Warnings:
1. Installation must be carried out by a
qualified engineer in accordance with
local regulations.
2. Disconnect supply before installing.
3. Install to a solid surface - vibrations may
cause mis-triggering.
4. Ensure environmental conditions are
suitable for electronic equipment
Note: the blinds are optional, they may be inserted behind the lens for focussing the detection range.
56
Note:We recommend the mounting distance between sensor to sensor
should be more than 2m to prevent sensors from false-triggering.
Direct junction "J" box mounting
a. Separate control board (A) from facia (B)
& junction box (C).
b. Make electrical connections to control board
(A). See detailed wiring diagram on next page.
c. Secure control board (A) to junction box (C).
Daylight
threshold d. Set-up sensor modes as per sections 3 & 4
of this manual.
Disable
e. Clip facial plate (B) to control board (A).
2Lux
10Lux
30Lux
10Lux
30Lux
Disable
2Lux
10Lux
30Lux
Disable
30Lux
10Lux
50Lux
Disable
2Lux

5. Wiring Diagram

L
N
P L'N N L
HIM11
1-10V
-
* Note: if neither function 5.2 nor 5.3 is desired, simply leave the "push" terminal disconnected.
Infrared receiver
HF Sensor module
Blind
A
Rotary switch preset
Blind
B
Surface mount assembly
a. Separate control board (A) from facia (B) &
Surface box (C).
b. Securely mount surface box (C) to a flat and
solid surface.
c. Make electrical connections to control board
(A). See detailed wiring diagram on next page.
d. Set-up sensor modes as per sections 3 & 4 of
this manual.
e. Secure control board (A) to surface box (C).
f. Clip facial plate (B) to control board (A).
C
56
A
B
+ -
L N
LED
LED driver
Max. 800W
+
1-10V
+
-
C - Surface box
B - Facia Cover
PIR
Photocell
LED indicator
Sensor mode selection
A - Control Board
C
56
A
B
+ -
L N
LED
LED driver
+
1-10V
-
HIM11-20190104-A1