Uplift Desk MON034 Quick Start Manual

Crestview Align Triple Monitor Arm
SKU: MON034 Base

Package Contents

Base
Base
Upper Clamp
Base Lower Arm
Upper Clamp
Upper Clamp
Adhesive Pad
Adhesive Upper
Pad Clamp
Adhesive Pad
Adhesive Pad
• Acceptable monitor weight range: 2.2 to 13.2 lb (per monitor)
Lower Clamp
• Recommended monitor size: up to 27"
• Desktop thickness compatibility: Clamp Method: 0.4"-3.3" thick. Bolt-through Method: 0.4"-1.8" thick
There are two ways to attach the Crestview Triple Monitor Arm to your desktop. If you would like to attach it along the back
edge of your desktop, follow the Clamp Method instructions on this page. If you prefer to attach it through your desktop,
Lower Clamp
follow the Bolt-Through Method instructions starting on page 2.
Lower Clamp
Wire Cover
Wire Cover
Wire Cover
Lower base plate
Lower base plate
Lower base plate

Clamp Method

Clamp Method
© UPLIFT Desk • 800-349-3839 • info@upliftdesk.com • upliftdesk.com
Upper Clamp
Upper Clamp
Lower Clamp
Vesa mount (x1)
Adhesive Pad
Adhesive Pad
Base
Lower Clamp
Vesa mount (x1)
Wire Cover
Base
Upper Clamp
Upper Arm VESA Plate
Adhesive Pad Base
Upper arm
(qty 3)
Wire Cover
Base Vesa mount (x1)
Lower Clamp
Upper Clamp Upper Clamp
Lower Clamp
Lower base plate
Base Vesa mount (x1)
3mm Allen wrench
Upper Clamp L
Lower base plate
Wire Cover
Lower Lower Adhesive Pad
Upper arm
Upper arm
Clamp Base Plate
Upper Clamp
Adhesive Pad
Lower base plate
Upper arm Base screw (x4)
Adhesive Pad
Lower arm
Lower Clamp
Lower arm
Adhesive Pad
Wire Cover
Lower Clamp
Lower arm
Wire Cover
Upper base plate
Lower Clamp
Wire Cover
Upper base plate
Lower arm
Lower Clamp Lower base plate
Upper base plate
Wire Cover
Lower base plate
Bar
Lower base plate
Lower base plate
Bar
Wire Cover
Upper base plate
Lower base plate
Bar
Bar
Bar
Bolt-Through Method
L
Adhesive Pad
Base screw (x4)
Upper arm
Upper arm
3mm Allen wrench 4mm Allen wrench
L M
Base Vesa mount (x1)
Lower arm 3mm Allen wrench 4mm Allen wrench
L M
Base Vesa mount (x1)
3mm Allen wrench
Vesa mount (x1)
L
Vesa mount (x1) 3mm Allen wrench 4mm Allen wrench 6mm Allen wrench
Lower Clamp
Upper Clamp
L M N
Bar
M4x12 bolt (x4)
Upper arm Base screw (x4) 3mm Allen wrench
Vesa mount (x1)
Upper Clamp
3mm Allen wrench 4mm Allen wrench
3mm Allen wrench
L
Adhesive Pad
Upper base plate Upper arm Base screw (x4)
Upper arm L Base screw (x4) L M4x12 bolt (x4) M M5x12 bolt (x4)
Adhesive Pad
Bar Ends
Lower arm
Vesa mount (x1) Lower arm
Base screw (x4)
N Bolt (x4)
3mm Allen wrench 4mm Allen wrench
L M
Lower Clamp
Lower arm
Lower arm
Upper base plate
N Bolt (x4)
Lower Clamp 3mm Allen wrench 4mm Allen wrench 6mm Allen wrench O Bolt (x4)
L M N
Wire Cover
Wire Cover
Upper base plate
M4x12 bolt (x4)
Upper arm Base screw (x4)
Upper base plate
4mm Allen wrench 6mm Allen wrench
Wire Cover
M N
Upper arm Base screw (x4)
Base screw (x4)
Upper arm
Wire Handle
M4x12 bolt (x4)
Bar Base screw (x4) Handle M5x12 bolt (x4)
Lower base plate
M4x12 bolt (x4)
Base screw (x4)
Bar Handle
Upper base plate
Cover
Lower base plate
Bar Handle
Lower arm
M4x12 bolt (x4) D5 Washers (x4)
M5x12 bolt (x4)
Bar Handle
N Bolt (x4)
N Bolt (x4)
Lower base plate O Bolt (x4)
Upper base plate
N Bolt (x4)
O Bolt (x4)
Lower arm
Lower arm
Bar Handle
Handle
Upper base plate
Bar
Handle
Upper base plate
Step 1
If you purchased the Crestview Monitor Arm Wiring
Kit, assemble that FIRST, before proceeding. Refer to
the separate instructions contained in the Crestview
Handle
Handle
Monitor Arm Wiring Kit (ACC076) package for com-
plete details.
Bar Handle
Handle
Step 2
Determine your mounting method. There are two
ways to attach the Crestview Align Triple Monitor
Arm to your desktop:
Clamp Method: If you would like to attach the monitor
arm along the back edge of your desktop, follow the
Clamp Method instructions (Steps 3 - 5) and ensure
your desk is between 0.4" and 3.3" thick.
Bolt-Through Method: If you prefer to attach the
monitor arm through your desktop, skip Steps 3 - 5
and follow the Bolt-Through Method instructions
(Steps 6 - 9) and ensure your desk is between 0.4"
and 1.8" thick.
Step 3 (Clamp Method)
A. Align the Upper Clamp with the Base in the ori-
entation shown. Attach using four M6x12 Flathead
Screws and the 4mm Allen Wrench.
B. Then peel the adhesive backing off of the Adhe-
sive Pad and attach it to the bottom of the Base
and Upper Clamp as shown. Align the pad with the
front edge of the Base first, then work to the back.
3mm Allen wrench 4mm Allen wrench
M N
L M
Upper arm
Lower arm
M4x12 bolt (x4)
M5x12 bolt (x4)
Adhesive Pad
Base screw (x4)
6mm Allen wrench
N
Lower arm
Upper base plate
6mm Allen wrench
Allen Wrenches N
N Bolt (x4)
O Bolt (x4)
4mm Allen wrench
6mm Allen wrench
(set of three: 3mm, 4mm, 6mm)
M N
Lower Clamp
M5x12 bolt (x4) D5 Washers (x4) 4mm Allen wrench
M6x12 Flathead Screw
6mm Allen wrench
4mm Allen wrench 6mm Allen wrench
M
M4x12 bolt (x4) D5 Washers (x4)
M5x12 bolt (x4)
D5 Washers (x4) M N N
M6x12 Panhead Screw
Upper base plate
M4x12 bolt (x4)
M5x12 bolt (x4)
6mm Allen wrench O Bolt (x4)
M6x22 Screw
N
N Bolt (x4)
O Bolt (x4)
M4x12 Screw (M-A)
Wire Cover
M5x12 bolt (x4) D5 Washers (x4)
M5x12 Screw (M-B)
Bar Handle
M4x12 bolt (x4)
M5x12 bolt (x4)
M4x12 bolt (x4)
D5 Washers (x4)
M5x12 bolt (x4)
M5 Washer (M-C)
O Bolt (x4)
N Bolt (x4)
O Bolt (x4)
Lower base plate
Bar
N Bolt (x4)
O Bolt (x4)
N Bolt (x4)
N Bolt (x4)
O Bolt (x4)
Handle
6mm Allen wrench
N
Base screw (x4)
N Bolt (x4)
D5 Washers (x4)
M4x12 bolt (x4)
M5x12 bolt (x4)
6mm Allen wrench
(qty 10)
Part for
N
Bolt-through assembly
(qty 4)
D5 Washers (x4)
(qty 2)
N Bolt (x4)
O Bolt (x4)
Upper Base Plate
(qty 12)
(qty 12)
D5 Washers (x4)
M5x12 bolt (x4)
D5 Washers (x4)
(qty 12)
Handle
Bar
O Bolt (x4)
M4x12 bolt
Upper arm
Lower arm
N Bolt (x
Upper base p
D5 Washers
1