Subscribe to Our Youtube Channel
Related Manuals for Uplift Desk Range-X MON062
Summary of Contents for Uplift Desk Range-X MON062
- Page 1 Range-X Dual Monitor Arm ® MON062 Scan QR code for product webpage For assembly assistance, visit upliftdesk.com/contact, or call 800-349-3839, or email info@upliftdesk.com ©2023 UPLIFT Desk®. All Rights Reserved...
- Page 2 Safety and Warnings Bolt-through CAUTION: Read all instructions before assembly. Failure to assemble or operate properly may result in damage or personal injury. Retain manual for future reference. WARNING: Desk, table, and other mounting surface build quality varies. Ensure the mounting surface is sufficient to support this monitor arm and a monitor.
- Page 3 Clamp Elbow by removing the two screws using the 4mm Allen Wrench as shown. Clamp Elbow 3. For thinner desktops (0.75’’ minimum), reattach the Clamp Elbow to the top two holes of the Clamp Base as shown. © UPLIFT Desk • 800-349-3839 • info@upliftdesk.com • upliftdesk.com...
-
Page 4: Bottom Plate
4. For thicker desktops (3.75’’ maximum), invert the orientation of the Clamp Elbow and reattach it to the lower two holes of the Clamp Base as shown. You will also need to remove the Clamp Bolt, flip it around, and reinsert it Reinsert with as shown so that the pointed end is pointed end... - Page 5 3. You will not need the Clamp Base for the Bolt-Through method. Using a Phillips Head Screwdriver, remove the three screws holding the Clamp Base to the Base Post. Clamp Base © UPLIFT Desk • 800-349-3839 • info@upliftdesk.com • upliftdesk.com...
- Page 6 Attach Bolt-Through Plate 4. Align the three large holes in the Base Post with the holes in the Bolt-Through Plate with the rubber pad facing away from the Base Post to protect the desktop. The logo on the Bolt-Through Plate should be oriented on the same side as the curved slot for the stopping pin at the top of the Base Post and opposite the set screw in the back of the Base...
-
Page 7: Step 3 - Arm Assembly
C. Loosely insert a Monitor Screw through each of the four holes in each VESA Mount. D. Once all four screws are started, tighten them using a Phillips head screwdriver. E. Ensure each VESA Mount is securely fastened to the monitors. © UPLIFT Desk • 800-349-3839 • info@upliftdesk.com • upliftdesk.com... - Page 8 Step 6 - Mount Monitor A. Slide the VESA Mount into the slots of the Monitor Joints. B. With one hand supporting the underside of the Monitor Joint and the other hand on top of the monitor, press down firmly on the top of the monitor until the tab on the VESA Mount clicks into place in the Monitor Joint.
-
Page 9: Step 9 - Wire Management
If it is difficult to adjust the monitor tilt angle, loosen the hex bolt on the Monitor Joint slightly with the included 13mm Flat Wrench. Adjust the tilt of the monitor and retighten the hex bolt. © UPLIFT Desk • 800-349-3839 • info@upliftdesk.com • upliftdesk.com... - Page 10 Notes...
- Page 11 Notes © UPLIFT Desk • 800-349-3839 • info@upliftdesk.com • upliftdesk.com...
- Page 12 © Copyright Notice: This guide is a component of this UPLIFT Desk product. This guide is a part of the scope of delivery, even if the item is resold. This guide is also available on the UPLIFT Desk website: upliftdesk.com. These specifications are subject to United States copyright law.
Need help?
Do you have a question about the Range-X MON062 and is the answer not in the manual?
Questions and answers