Uplift Desk MON042 Quick Start Manual

Enfield Dual Monitor Arm
SKU: MON042
Package Contents Package Contents
Base Lower Arm
(qty 2)
Base
Upper Clamp Lower Clamp
Upper Clamp
Adhesive Pad
• Acceptable monitor weight range: 4.4 lb to 19.8 lb (per monitor)
• Recommended monitor size: up to 32" (measured diagonally)
Lower Clamp
• Desktop thickness compatibility:
• Clamp Method: 0.4"-3.3" thick.
Wire Cover
• Bolt-through Method: 0.4"-3.1" thick
There are two ways to attach the Enfield Dual Monitor Arm to your desktop. If you would like to attach it along the back
Lower base plate
edge of your desktop, follow the Clamp Method instructions starting on this page. If you prefer to attach it through your
desktop, follow the Bolt-Through Method instructions starting on page 2.
Clamp Method
Clamp Method
© UPLIFT Desk • 800-349-3839 • info@upliftdesk.com • upliftdesk.com
Base
Base Vesa mount (x1)
Upper Arm VESA Plate
Upper Clamp
(qty 2)
Base Vesa mount (x1)
3mm Allen wrench
L
Upper Clamp Adhesive Pad
Vesa mount (x1)
Upper arm
3mm Allen wrench 4mm Allen wrench
L M
Upper Clamp
Adhesive Pad
Upper arm Base screw (x4)
Lower Clamp
Wire Cover
Adhesive Pad
Lower arm
M4x12 bolt (x4)
Upper arm Base screw (x4)
Wire Cover
Lower Clamp
Lower arm
Upper base plate
Lower Clamp Lower base plate
Lower arm
Wire Cover
N Bolt (x4)
Upper base plate
Wire Cover
Upper base plate
Lower base plate
Bar
Lower base plate
Bar Handle
Bar Handle
Bolt-Through Method
Allen Wrenches
(set of two: 4mm, 6mm)
Vesa mount (x1)
Flat Wrench
3mm Allen wrench 4mm Allen wrench 6mm Allen wrench
L M N
3mm Allen wrench 4mm Allen wrench 6mm Allen wrench
M6x12 Flathead Screw
L M N
(qty 2)
M4x12 bolt (x4)
Upper arm Base screw (x4) M5x12 bolt (x4)
4mm Allen wrench 6mm Allen wrench
M4x12 Screw (M-A)
M N
M4x12 bolt (x4)
Base screw (x4) M5x12 bolt (x4)
6mm Allen wrench
M5x12 Screw (M-B)
N Lower arm
N Bolt (x4)
M4x12 bolt (x4)
M5x12 bolt (x4) D5 Washers (x4)
M5 Washer (M-C)
Upper base plate
M5x12 bolt (x4) D5 Washers (x4)
N Bolt (x4)
O Bolt (x4)
N Bolt (x4)
O Bolt (x4)
Bar Handle
O Bolt (x4)
Handle
Step 1
Determine your mounting method. There are two
ways to attach the Enfield Dual Monitor Arm to your
desktop:
Clamp Method: If you would like to attach the monitor
arm along the back edge of your desktop, follow the
Clamp Method instructions (Steps 2 - 4).
Bolt-Through Method: If you prefer to attach the
monitor arm through your desktop, skip Steps 2 - 4
and follow the Bolt-Through Method instructions
(Steps 5 - 7).
Step 2 (Clamp Method)
Align the Upper Clamp with the Base in the orienta-
tion shown and attach it using the three M6x12 Flat-
head Screws and the 4mm Allen Wrench.
(qty 3)
D5 Washers (x4)
(qty 8)
D5 Washers (x4)
(qty 8)
O Bolt (x4)
(qty 8)
Parts for
Bolt-through assembly
Upper Base Plate
Long Bolt
Lower Base Plate
M8 Washer
M8 Nut
1