Analog_Input Objects - ABB GE ReliaGear AMP1 Installation Instructions Manual

A M P 1 I N T E G R AT E D P O W E R A N D E N E R G Y I N S TA L L AT I O N I N S T R U C T I O N S
AMP1

Analog_input objects

Use the Present_Value property of the Analog_Input objects
for all read-only numeric variables in the meter other than
those used specifically for device configuration (in the Device
Object) or data logging (in the Trend_Log objects).
These objects support the Description and Reliability object
properties and all required Analog_Input object properties.
None of them are writable. The values that are not
instantaneous (i.e., Accumulated Energy, Max Demand, Pulse
Input Counts) are non-volatile. They are not updated while
No. Name Description
AV1 Energy Real Energy Consumption
AV2 kW_Total Total Real Power
AV3 kVAR_Total Total Reactive Power
AV4 kVA_Total Total Apparent Power
AV5 PF_Total Total Power Factor
AV6 Volts_LL_Avg Voltage L-L Average
AV7 Volts_LN_Avg Voltage L-N Average
AV8 Current_Avg Current Average
AV9 kW_A Real Power Phase A
AV10 kW_B Real Power Phase B
AV11 kW_C Real Power Phase C
AI12 PF_A Power Factor Phase A
AI13 PF_B Power Factor Phase B
AI14 PF_C Power Factor Phase C
AI15 Volts_AB Votlage Phase A-B
AI16 Volts_BC Voltage Phase B-C
AI17 Volts_AC Voltage Phase A-C
AI18 Volts_AN Voltage Phase A-N
AI19 Volts_BN Voltage Phase B-N
AI20 Volts_CN Voltage Phase C-N
AI21 Current_A Current Phase A
AI22 Current_B Current Phase B
AI23 Current_C Current Phase C
AI24 Reserved_AI24 Reserved
AI25 Frequency Frequency
Apparent Energy
AI26 kVAh
Consumption
Reactive Energy
AI27 kVARh
Consumption
AI28 kVA_A Apparent Power Phase A
AI29 kVA_B Apparent Power Phase B
AI30 kVA_C Apparent Power Phase C
AI31 KVAR_A Reactive Power Phase A
AI32 KVAR_B Reactive Power Phase B
AI33 KVAR_C Reactive Power Phase C
KW_Present_ Total Real Power Present
AI34
Demand Demand
KVAR_Present_ Total Reactive Power
AI35
Demand Present Demand
KVA_Present_ Total Apparent Power
AI36
Demand Present Demand
For troubleshooting or service related questions, contact ABB at 800-782-8061 or at epis.component.support@abb.com
control power is inactive, but their past values are retained
when power is restored.
For complete assurance, check the Reliabilty property for a
No_ Fault_Detected status before reading the Present_Value.
If the line voltage or input frequency of the system being
monitored falls out of the supported range, the corresponding
alert bits (BI1-BI7) are set and the reliability property of any
values that cannot be accurately measured under those
conditions returns Unreliable_Other.
R/W NV Units Range
R NV kWh 0 - 3.4+E38
R – kW 0 - Max_Power (AI45)
R – kVAR 0 - Max_Power (AI45)
R – kVA 0 - Max_Power (AI45)
R – Power Factor 0.00 - 1.00
R – Volts –
R – Volts –
R – Amps –
R – kW 0 - Max_Power (AI45)
R – kW 0 - Max_Power (AI45)
R – kW 0 - Max_Power (AI45)
R – Power Factor 0.00 - 1.00
R – Power Factor 0.00 - 1.00
R – Power Factor 0.00 - 1.00
R – Volts –
R – Volts –
R – Volts –
R – Volts –
R – Volts –
R – Volts –
R – Amps –
R – Amps –
R – Amps –
R – n/a –
R – Hz 45.0-65.0
R NV kVAh 0 - 3.4+E38
R NV kVARh 0 - 3.4+E38
R – kVA 0 - Max_Power (AI45)
R – kVA 0 - Max_Power (AI45)
R – kVA 0 - Max_Power (AI45)
R – kVAR 0 - Max_Power (AI45)
R – kVAR 0 - Max_Power (AI45)
R – kVAR 0 - Max_Power (AI45)
R – kW 0 - Max_Power (AI45)
R – kVAR 0 - Max_Power (AI45)
R – kVA 0 - Max_Power (AI45)
Additional information
–
–
–
–
1.00 for 100%
–
–
–
–
–
–
1.00 for 100%
1.00 for 100%
1.00 for 100%
–
–
–
–
–
–
–
–
–
Returns QNAN or any value
Returns QNAN if frequency is out of range (or no voltage
input present on Phase A)
The UNITS property of object AI26 reports that these
units are kWh because there is no unit type in the
BACnet standard for kVAh.
The UNITS property of object AI27 reports that these
units are kWh because there is no unit type in the
BACnet standard for kVARh.
–
–
–
–
–
–
–
–
–
table continued on next page
21