Related Manuals for Belson Outdoors RPD8
Summary of Contents for Belson Outdoors RPD8
- Page 1 111 North River Road North Aurora, IL 60542 Phone: (800) 323-5664 Fax: (630) 897-0573 sales@belson.com Model # RPD8 Instructions Sheet RECYCLED PLASTIC DELUXE PICNIC TABLE www.belson.com...
- Page 2 BEFORE ASSEMBLY, PLEASE MAKE SURE ALL COMPONENTS ARE INCLUDED. FP - FASTENER PACK C - TABLE TOP ( 1 ) ONE FASTENER PACK ( 1 ) - ONE TABLE TOP D - SEAT ( 2 ) - TWO SEATS M - RIGHT LEG ( 1 ) - ONE RIGHT SMALL LEG L - LEFT LEG G - UNDER SEAT SUPPORT...
- Page 3 BEFORE ASSEMBLY, PLEASE MAKE SURE ALL FASTENERS ARE INCLUDED. 16 - 3/8” X 5” HEX HEAD BOLT 8 - 3/8” X 3” HEX HEAD LAG BOLT 46 - 3/8” FLAT WASHER 16 - 3/8” NYLON LOCK NUT 8 - #12 X 3” FLAT HEAD PHILLIPS SCREW ALSO NEEDED FOR THIS ASSEMBLY WILL BE THE FOLLOWING MATERIALS: 1 - #3 PHILLIPS DRIVE BIT 2 - 9/16”...
- Page 4 COUNTER BORE 3/8” FLAT WASHER 3/8” NYLON LOCK NUT 3/8” FLAT WASHER 3/8” X 5” HEX HEAD BOLT STEP #1: WHILE THE TABLE TOP IS UPSIDE-DOWN, FASTEN THE LARGE LEGS TO THE LEFT AND RIGHT TOP SUPPORTS BEING SURE THAT THE COUNTER BORES ARE POINTING TOWARD THE CENTER OF THE TABLE AS SHOWN ABOVE.
- Page 5 COUNTER BORE 3/8” FLAT WASHER 3/8” X 5” HEX HEAD BOLT STEP #2: WHILE THE TABLE TOP IS UPSIDE - DOWN, FASTEN THE SMALL LEGS TO THE CENTER TOP SUPPORT BEING SURE THAT THE COUNTER BORES ARE POINTING AWAY FROM THE TOP SUPPORT AS SHOWN ABOVE.
- Page 6 3/8” FLAT WASHER 3/8” NYLON LOCK NUT STEP #3: WHILE THE TABLE TOP IS UPSIDE-DOWN, FASTEN THE SEAT CROSS SUPPORTS TO THE LARGE LEGS. USE ( 1 ) ONE 3/8” X 5” HEX HEAD BOLT AND ( 1 ) ONE 3/8” FLAT WASHER ALONG WITH ( 1 ) ONE 3/8” FLAT WASHER AND ( 1 ) ONE 3/8”...
- Page 7 3/8” FLAT WASHER 3/8” NYLON LOCK NUT 3/8” FLAT WASHER 3/8” X 5” HEX HEAD BOLT STEP #4: WHILE THE TABLE TOP IS UPSIDE-DOWN, FASTEN THE CENTER SUPPORT TO THE SMALL LEGS. USE ( 1 ) ONE 3/8” X 5” HEX HEAD BOLT AND ( 1 ) ONE 3/8” FLAT WASHER ALONG WITH ( 1 ) ONE 3/8” FLAT WASHER AND ( 1 ) ONE 3/8”...
- Page 8 STEP #5: WHILE THE TABLE TOP IS UPSIDE-DOWN, FASTEN THE UNDER SEAT SUPPORTS TO THE SEAT CROSS SUPPORTS. USE ( 1 ) ONE 3/8” X 3” HEX HEAD LAG BOLT AND ( 1 ) ONE 3/8” FLAT WASHER PER HOLE TO SECURE.
- Page 9 STEP #7: FLIP THE TABLE UPRIGHT ONTO THE LEGS. PLEASE TAKE CAUTION WHILE FLIPPING THE TABLE. AT THIS POINT IN ASSEMBLY THE TABLE WEIGHS APPROXIMATELY 315 POUNDS. www.belson.com...
- Page 10 #12 X 3” FLAT HEAD PHILLIPS SCREW STEP #8: WHILE THE TABLE IS UPRIGHT FASTEN THE SEATS TO THE SEAT CROSS SUPPORTS BEING SURE TO CENTER ALL HOLES OVER BOARDS. USE ( 1 ) ONE #12 X 3” FLAT HEAD PHILLIPS SCREW PER HOLE TO SECURE.