Related Manuals for Belson Outdoors BST-01
Summary of Contents for Belson Outdoors BST-01
- Page 1 111 North River Road North Aurora, IL 60542 Phone: (800) 323-5664 Fax: (630) 897-0573 sales@belson.com Model # BST-01 Instructions Sheet BISTRO PICNIC TABLE www.belson.com...
- Page 2 BEFORE ASSEMBLY, PLEASE MAKE SURE ALL COMPONENTS ARE INCLUDED. FP - FASTENER PACK R - TABLE CENTER ( 1 ) - ONE FASTENER PACK ( 2 ) - TWO TABLE CENTERS J - TABLE TOP N - SEAT ( 1 ) - ONE TABLE TOP ( 4 ) - FOUR SEATS H - TABLE LEG Q - SEAT SUPPORT...
- Page 3 BEFORE ASSEMBLY, PLEASE MAKE SURE ALL FASTENERS ARE INCLUDED. 8 - 3/8” X 4-1/2” HEX HEAD BOLT 16 - 3/8” FLAT WASHER 8 - 3/8” NYLON LOCK NUT 8 - #12 X 3” FLAT HEAD PHILLIPS SCREW 64 - #12 X 1” PAN HEAD PHILLIPS SCREW ALSO NEEDED FOR THIS ASSEMBLY WILL BE THE FOLLOWING MATERIALS: 1 - 3”...
- Page 4 3/8” FLAT 3/8” x 4-1/2” HEX WASHER HEAD BOLT 3/8” FLAT WASHER 3/8” NYLON LOCK NUT STEP #1: SLIDE ( 1 ) ONE TABLE CENTER ONTO EACH END OF THE TABLE LEG AS SHOWN ABOVE. USE ( 1 ) ONE 3/8” X 4-1/2” HEX HEAD BOLT AND ( 1 ) ONE 3/8” FLAT WASHER ALONG WITH ( 1 ) ONE 3/8” FLAT WASHER AND ( 1 ) ONE 3/8”...
- Page 5 3/8” NYLON LOCK NUT 3/8” FLAT WASHER 3/8” FLAT WASHER 3/8” x 4-1/2” HEX HEAD BOLT STEP #2: SLIDE THE REMAINING ( 3 ) THREE TABL LEGS IN TO THE TABLE CENTERS. USE ( 1 ) ONE 3/8” X 4-1/2” HEX HEAD BOLT AND ( 1 ) ONE 3/8” FLAT WASHER, ALONG WITH ( 1 ) ONE 3/8” FLAT WASHER AND ( 1 ) ONE 3/8”...
- Page 6 #12 X 1” PAN HEAD PHILLIPS SCREW STEP #3: PLACE THE TABLE TOP UPSIDE DOWN ONTO A PIECE OF CARDBOARD OR ANOTHER SOFT SURFACE, TO PROTECT IT DURING INSTALLATION. PLACE THE LEG ASSEMBLY ONTO THE TABLE TOP AS SHOWN ABOVE. ALIGN THE PRE-DRILLED HOLES IN THE TABLE LEGS WITH THE PILOT HOLES IN THE TABLE TOP.
- Page 7 #12 X 3” FLAT HEAD PHILLIPS SCREW STEP #4: WHILE THE TABLE IS UPSIDE DOWN, ALIGN THE PRE-DRILLED HOLES IN THE TABLE LEG TO THE PILOT HOLES IN THE SEAT SUPPORT, AS SHOWN ABOVE. USE ( 1 ) ONE #12 X 3” FLAT HEAD SCREW PER HOLE TO SECURE.
- Page 8 #12 X 1” PAN HEAD PHILLIPS SCREW STEP #5: WHILE THE TABLE IS UPSIDE DOWN, ALIGN THE PRE-DRILLED HOLES IN THE SEAT TO THE PILOT HOLES IN THE SEAT SUPPORT AND THE TABLE LEG AS SHOWN ABOVE. USE ( 1 ) ONE #12 X 1” PAN HEAD SCREW PER HOLE TO SECURE.
- Page 9 STEP #6: TURN THE TABLE OVER ON TO ITS LEGS, PLEASE USE CAUTION FOR THE TABLE WEIGHS APPROXIMATELY 200 POUNDS. www.belson.com...