Related Manuals for Belson Outdoors RECYCLED PLASTIC ROUND TABLE RT-100
Summary of Contents for Belson Outdoors RECYCLED PLASTIC ROUND TABLE RT-100
- Page 1 111 North River Road North Aurora, IL 60542 Phone: (800) 323-5664 Fax: (630) 897-0573 sales@belson.com Model # RT-100 Instructions Sheet RECYCLED PLASTIC ROUND TABLE www.belson.com...
- Page 2 BEFORE ASSEMBLY, PLEASE MAKE SURE ALL COMPONENTS ARE INCLUDED. F - SMALL SPOKE ASSEMBLY B - PLASTIC BRACKET ( 12 ) - TWELVE PLASTIC BRACKET J - TABLE TOP ( 1 ) - ONE TABLE TOP W/ SMALL SPOKE ASSEMBLY FP - FASTENER PACK ( 1 ) - ONE FASTENER PACK A - LEG SUPPORT...
- Page 3 BEFORE ASSEMBLY, PLEASE MAKE SURE ALL FASTENERS ARE INCLUDED. 18 - 3/8” X 5” HEX HEAD BOLT 36 - 3/8” FLAT WASHER 18 - 3/8” NYLON LOCK NUT 6 - #12 X 3” FLAT HEAD PHILLIPS SCREW 12 - #12 X 2 1/2” FLAT HEAD PHILLIPS SCREW 48 - #12 X 2”...
- Page 4 STEP #1: ASSEMBLE THE LARGE SPOKES TO THE CENTER PROPELLER AS SHOWN BELOW. USE ( 1 ) ONE 3/8” X 5” HEX HEAD BOLT AND ( 1 ) ONE 3/8” FLAT WASHER, ALONG WITH ( 1 ) ONE 3/8” FLAT WASHER AND ( 1 ) ONE 3/8”...
- Page 5 3/8” NYLON LOCK NUT 3/8” X 5” HEX HEAD BOLT 3/8” FLAT WASHER 3/8” FLAT WASHER STEP #3: PLACE THE TABLE TOP ASSEMBLY UPSIDE DOWN ONTO A PIECE OF CARDBOARD OR ANOTHER SOFT SURFACE TO PROTECT IT DURING INSTALLATION. PLACE THE LARGE SPOKE ASSEMBLY ONTO THE SMALL SPOKE ASSEMBLY AS SHOWN ABOVE.
- Page 6 3/8” NYLON LOCK NUT 3/8” X 5” HEX HEAD BOLT 3/8” FLAT WASHER 3/8” FLAT WASHER STEP #4: WHILE THE TABLE IS UPSIDE DOWN, SLIDE THE LARGE SPOKE ASSEMBLY UP TO MATCH THE HOLES TO THE LEGS. SECURE THE LARGE SPOKE ASSEMBLY TO THE LEGS AS SHOWN ABOVE. USE ( 1 ) ONE 3/8”...
- Page 7 STEP #5: PLACE THE 7” PLASTIC BRACKETS ONTO THE SEAT SUPPORTS AS SHOWN BELOW. ALIGN THE PRE-DRILLED HOLES IN THE PLASTIC BRACKETS WITH THE PILOT HOLES IN THE SEAT SUPPORTS. USE ( 1 ) ONE #12 X 2” FLAT HEAD PHILLIPS SCREW PER HOLE TO SECURE. #12 X 2 1/2”...
- Page 8 #12 X 3” FLAT HEAD PHILLIPS SCREW STEP #7: WHILE THE TABLE IS UPSIDE DOWN, PLACE THE SEAT SUPPORT ASSEMBLY ONTO THE LEGS AS SHOWN ABOVE. ALIGN THE PRE-DRILLED HOLES IN THE SEAT SUPPORT ASSEMBLY WITH THE PILOT HOLES IN THE LEGS. USE ( 1 ) ONE #12 X 3” FLAT HEAD PHILLIPS SCREW PER HOLE TO SECURE. www.belson.com...
- Page 9 STEP #8: WHILE THE TABLE IS UPSIDE DOWN, FASTEN THE SEATS TO THE LARGE SPOKE ASSEMBLY AND SEAT SUPPORT ASSEMBLIES AS SHOWN BELOW. ALIGN THE PRE-DRILLED HOLES IN THE LARGE SPOKE ASSEMBLY AND SEAT SUPPORT ASSEMBLIES WITH THE PILOT HOLES IN THE SEATS. USE ( 1 ) ONE #12 X 2”...