Advertisement
C. Registering the Number of Punch Hole
Perform the following to register the type of punch unit (number of
holes) used to the IC on the punch controller PCB for identification
by the finisher. Be sure to register the type whenever you have
replaced the punch controller PCB.
1)
Set bits 1 through 4 on the DIPSW1001 on the punch control-
ler PCB as follows:
ON
1
2)
Press SW1002 on the punch controller PCB to select the
appropriate number of punch holes.
• Each press on SW1002 moves the selection through the fol-
lowing (repeatedly from top to bottom).
Number of punch holes
2 holes (Punch Unit-J1)
2/3 holes (Punch Unit-K1)
4 holes (Punch Unit-G1)
4 holes (Punch Unit-H1)
3)
Press SW1003 on the punch controller PCB twice. The
presses will store the selected number of punch holes on the
punch controller PCB.
• A single press on SW1003 will cause the LED indication to
flash; another press on SW1003 will cause the indication to
remain ON to indicate the end of registration.
4)
Shift all bits of DIPSW1001 to OFF.
D. After Replacing the EEP-ROM (IC1002)
1)
Turn off the host machine.
2)
Set bits 1 through 4 on the punch controller PCB as follows:
ON
1
3)
Press SW1002 and SW1003 on the punch controller PCB at
the same time.
• The presses will initialize the EEP-ROM. At the end, all
LEDs (LED1001, LED1002, LED1003) will go ON.
4)
Adjust the sensor output, and store the number of punch
holes. Adjust the punch hole position adjustment (horizontal
registration) of necessary.
2
3
4
LED1001
LED1002
LED1003
ON
OFF
OFF
ON
ON
OFF
OFF
ON
OFF
OFF
OFF
ON
2
3
4
MX-FNX2/AR-PN1/MX-RBX1 ADJUSTMENTS 8 – 2
E. Setup by the diag simulation of the host
machine
1)
Select "FINISHER ADJUSTMENT" in SIM 3-10.
2)
Select a setup item and change the setup value.
SIMULATION NO.03-10
TEST
FINISHER ADJUSTMENT
A:200
; SADDLE POSITION
A:
200
B:200
; FOLDING POSITION
C: 10
; FRONT ADJUSUT
[197-203]
D:100
; REAR ADJUSUT
SIMULATION NO.03-10
TEST
FINISHER ADJUSTMENT
A:197
; SADDLE POSITION
A:
197
B:200
; FOLDING POSITION
C: 10
; FRONT ADJUSUT
[197-203]
D:100
; REAR ADJUSUT
Adjustable setup range is as follows.
Adjustment content
1
Saddle binding position
adjustment
2
Saddle folding position
adjustment
3
Front alignment position
adjustment
4
Rear alignment position
adjustment
5
Staple front one-position
binding position adjustment
6
Staple rear one-position
binding position adjustment
7
Staple 2-position binding
center adjustment
8
Staple 2-position binding
pitch adjustment
9
Punch center position
adjustment (FR direction)
10
Punch hole position
adjustment (paper feed
direction)
CLOSE
10-key
OK
CLOSE
Default
Setup
Change/Setup
value
range
value 1
200
0 - 400
0.0707mm
200
0 - 400
0.0525mm
10
0 - 20
0.367mm
10
0 - 20
0.367mm
100
0 - 200
0.04374mm
100
0 - 200
0.04374mm
100
0 - 200
0.04374mm
50
0 - 100
0.04374mm
50
47 - 53
50
0 - 100
0.105mm
0
OK
0
OK
Advertisement
Chapters
