1. Manuals
  2. Brands
  3. Touchboards Manuals
  4. Racks & Stands
  5. peerless CPA100WALLARM
  6. Installation and assembly manual

Touchboards peerless CPA100WALLARM Installation And Assembly Manual

Hitachi short throw wall arm
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Installation and Assembly: Hitachi Short Throw Wall Arm
Model: CPA100WALLARM
Maximum Load Capacity: 50 lb (22.7 kg)
1 of 12
ISSUED: 03-17-08 SHEET #:055-9499-4 08-15-08
3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com
Visit the Peerless Web Site at www.peerlessmounts.com
For customer care call 1-800-865-2112 or 708-865-8870.

Advertisement

Table of Contents
loading

Related Manuals for Touchboards peerless CPA100WALLARM

Summary of Contents for Touchboards peerless CPA100WALLARM

  • Page 1 Installation and Assembly: Hitachi Short Throw Wall Arm Model: CPA100WALLARM Maximum Load Capacity: 50 lb (22.7 kg) 1 of 12 ISSUED: 03-17-08 SHEET #:055-9499-4 08-15-08 3215 W. North Ave. • Melrose Park, IL 60160 • (800) 865-2112 or (708) 865-8870 • Fax: (708) 865-2941 • www.peerlessmounts.com Visit the Peerless Web Site at www.peerlessmounts.com For customer care call 1-800-865-2112 or 708-865-8870.

  • Page 2: Wall Construction

    NOTE: Read entire instruction sheet before you start installation and assembly. WARNING • Do not begin to install your Peerless product until you have read and understood the instructions and warnings contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please call Peerless customer care at 1-800-865-2112.

  • Page 3: Parts List

    Before you begin, make sure all parts shown are included with your product. Parts List Description Qty. Part # A slide plate 055-1821 B projector mount assembly 055-1803 C #10-32 x 3/8" serrated washer head socket pin screw 520-1151 D #10-32 x 1/4" socket pin screw 520-1196 E 5/32"...
  • Page 4 Projector Position NOTE: Use the chart (see fig 1.1) below to determine the placement of projector in relation to mounting location of wall arm. Chart numbers will have a 3% discrepancy due to the optics of the projector. Prior to installing projector, physically test the projection size and distance while having the actual projector in the desired location before installing, this will determine the exact mounting position.

  • Page 5: Installation To Wood Stud Wall

    Installation to Wood Stud Wall WARNING • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components. • Tighten wood screws so that wall plate is firmly attached, but do not overtighten. Overtightening can damage the screws, greatly reducing their holding power.

  • Page 6: Installation To Solid Concrete Or Cinder Block

    Installation to Solid Concrete or Cinder Block WARNING • When installing Peerless wall mounts on cinder block, verify that you have a minimum of 1-3/8" of actual concrete thickness in the hole to be used for the concrete anchors. Do not drill into mortar joints! Be sure to mount in a solid part of the block, generally 1"...
  • Page 7 Installation to Metal Stud Wall (Metal Stud Accessory Kit ACC 415 Required) WARNING • Drywall must be 1/2" or thicker, and metal stud must be 24 gauge or thicker. • Installer must verify that the supporting surface will safely support the combined load of the equipment and all attached hardware and components.
  • Page 8 Place vinyl trim (W) onto bottom or top of wall plate (K) Hook wall arm (J) onto wall plate (K) as shown in where cords will be routed as shown in fig. 3.1. fig. 3.2 or for additional vertical adjustment fig. 3.3. Run cords through desired opening at this point.

  • Page 9: Front View

    NOTE: Do not tighten 1/4-20 x 1" hex head screws (M) fully to allow for adjustment. Fasten projector mount assembly (B) to wall arm (J) using two 1/4-20 x 1" hex head screws (M), 0.509" ID spacers (O), 1/4"ID spacers (N), 0.376 ID shoulder spacers (P) and slide plate (A) as shown in fig.

  • Page 10: Attaching Adapter Plate To Projector

    Attaching Adapter Plate to Projector Align shoulder on connection block opposite notch in CONNECTION adapter plate (L). Attach adapter plate (L) to BLOCK connection block from projector mount assembly (B) SHOULDER using two #10-32 x 3/8" serrated washer head socket pin screws (C) as shown in figure 6.1.

  • Page 11: Attaching Adapter Plate To Projector Mount

    Attaching Adapter Plate to Projector Mount WARNING • Do not lift more weight than you can handle. Use additional man power or mechanical lifting equipment to safely handle placement of the projector. Slide connection block with projector into projector mount assembly (B) as shown. Tighten captive screw to secure projector to projector mount assembly (B).

  • Page 12: Projector Alignment

    Projector Alignment To adjust yaw (swivel): Loosen screw on projector mount assembly (B) indicated below until projector mount can be rotated. Rotate mount to desired position and retighten screw. To adjust pitch (forward and backward tilt): Turn knob on back of mount as shown below. Pull knob out and turn by hand for easy adjustment or insert #2 phillips screwdriver in end of knob and turn.

Table of Contents