Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Touchboards CHIEF FCI
Summary of Contents for Touchboards CHIEF FCI
- Page 1 I N S T A L L A T I O N I N S T R U C T I O N S PACI Interactive Flat Panel Upgrade Kits Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description FCI / PACI...
-
Page 2: Installation Instructions
FCI / PACI Installation Instructions DISCLAIMER WARNING: Failure to provide adequate structural strength Milestone AV Technologies and its affiliated corporations and for this component can result in serious personal injury or subsidiaries (collectively "Milestone"), intend to make this damage to equipment! It is the installer’s responsibility to manual accurate and complete. - Page 3 Installation Instructions FCI / PACI DIMENSIONS 140° COVERAGE ANGLE FOR BEST RESULTS: SLIDE THE SENSOR OUT UNTIL THE CORNERS OF THE TV ARE WITHIN THE COVERAGE AREA 0.50 12.7 RECOMMENDED SPACING...
- Page 4 FCI / PACI Installation Instructions DIMENSIONS - continued PACI 14.00 355.7 0.50 12.7 RECOMMENDED SPACING 140° SENSOR COVERAGE SLIDE SENSOR SO THAT CORNERS OF TV ARE INSIDE COVERAGE AREA LIKE SHOWN ABOVE.
- Page 5 Installation Instructions FCI / PACI LEGEND Tighten Fastener Pencil Mark Apretar elemento de fijación Marcar con lápiz Befestigungsteil festziehen Stiftmarkierung Apertar fixador Marcar com lápis Serrare il fissaggio Segno a matita Bevestiging vastdraaien Potloodmerkteken Serrez les fixations Marquage au crayon Loosen Fastener Drill Hole Aflojar elemento de fijación...
-
Page 6: Tools Required For Installation
FCI / PACI Installation Instructions TOOLS REQUIRED FOR INSTALLATION 1/8" (included- 3/16" (included - both models) FCI only) PARTS FCI Only B (2) D (1) A (2) [FCI 3"-5" 10-24 x 3/8" ClickConnect extension Interactive Hardware bracket] E (2) Kit (PACI Only) [Interactive bar assembly] C (1) -
Page 7: Pre-Installation Information
Installation Instructions FCI / PACI PRE-INSTALLATION INFORMATION Compatibility An up-to-date list of the flat panel TV models recommended for use with Chief’s FCI and PACI interactive kits can be found at www.chiefmfg.com/Interactive-Mounts. The recommended flat panel models all have the same display requirements: •... - Page 8 FCI / PACI Installation Instructions Insert interactive bar assembly (E) into flat panel mount, turning bars until tightened into flat panel mount. (See (back view) Figure 4) Flat panel mount (front view) Figure 4 Figure 6 Fasten sensor assembly (F) to bars (E) using two 5/16 x 5/8" button head cap screws (G).
- Page 9 Installation Instructions FCI / PACI Holes are provided in the faceplate for use with a padlock or CONNECTING FCI/PACI similar locking device, if desired. In addition, the pin and nut may be removed from the upper holes and moved to the lower holes NOTE: Follow instructions in the Quick Start Guide (KE).
-
Page 10: Sensor Location
FCI / PACI Installation Instructions Sensor Location Lateral extension NOTE: The FCI and PACI may be mounted to the left or right dimension side of a flat panel screen. The green sensor light Edge of flat 3" needs to always be oriented so that it is closest to panel TV screen [76.2mm] screen. - Page 11 Installation Instructions FCI / PACI Perform the grid test to see if there are any inconsistencies. a. Open eBeam software (See Figure 13) FAILED grid test Distorted annotation lines PASSED grid test Figure 13 b. Go to Full Screen view (See Figure 14) Figure 15 If the grid test has failed, gradually move the sensor assembly in 1/2"...
- Page 12 FCI / PACI Installation Instructions Checking System Diagnostics Right click on the E-Beam icon on the system tray to open the software. Select Interactive Options. (See Figure 16) Select System Preferences. Select Hardware Diagnostics. Record the 3 numbers that appear in Hardware Diagnostics (See Figure 16) Compare hardware diagnostics results to table below.
- Page 13 Installation Instructions FCI / PACI...