Page 1
DCS1A the Document Camera Stand - Assembly Guide DCS2A For assistance, please contact us: Assembly Guide DCS1A_DCS2A_2014_E 1-800-267-8494 Check out our other products online at Email info@copernicused.com www.copernicused.com Have your packing slip ready for reference This product is meant to be assembled by an adult. WARNING In its unassembled state, small parts present a hazard.
Page 2
Warning! Hazard Risks! Please read the warnings below for important safety information regarding your product. Failure to read these warnings or to follow the instructions below could result in personal injury or damage to your product that could void your warranty. In its unassembled state, this product contains parts that can be hazardous to small children.
Page 3
DCS1A Tips for Assembly DCS2A Watch for These Helpful Symbols This symbol denotes a 2 Person Task. For safety, please ensure that there are two people working on steps displaying this symbol 2 Person Watch for this symbol throughout the Assembly Instructions. Wherever you see it, pay close attention.
Page 4
DCS1A Dewey the Document Camera Stand - Assembly Guide DCS2A Please note that in its unassembled state, this product contains parts WARNING that can be hazardous to small children. This product should be assembled by an adult. iPad mini™ Spacer (1) Headphone Top Arm Pre-Assembly (1) Hanger (1)
Page 5
DCS1A Dewey - Parts DCS2A Before beginning, you should have: Contents - Box 1 Hardware Actual Size In Box 1 Top Arm Positioning Template M6 x 20mm Portrait Position Landscape Position for 8.5” x 11” Paper for 8.5” x 11” Paper iPad &...
Actual Size: M6 x 20mm You will need: (Not to Scale) Outer Tube Base Assemble the Outer Tube to the Base Make sure the stop hole is facing inwards and is placed on top. Actual Size: You will need: (Not to Scale) Inner Tube Place the Inner Tube inside the Outer Tube Pay close attention to the...
Page 7
Actual Size: M6 x 45mm M6 Lock Washer You will need: (Not to Scale) Top Arm Headphone Holder Assemble the Top Arm & Headphone Holder The headphone holder holds up to two headphones. To easily assemble the Top Arm, adjust the height to the lowest position then assemble the pieces together.
Actual Size: You will need: (Not to Scale) Positioning Template Position the Paper Template (OPTIONAL) Pay close attention to the orientation of iPad and 8.5”x11” paper. Then match the edge of the paper with the indicated line that the arrow points at. This helps to position your paper in the middle of your projection.
Page 9
Actual Size: You will need: (Not to Scale) Magnetic LED Light OPTIONAL - FOR DCS2A Positioning the Magnetic LED Light (OPTIONAL) Use the magnet on the LED to attach it anywhere on Dewey’s Neck. Suggested spots to mount the Magnetic LED Light without getting hot spots.
Page 10
the Document Camera Stand - Tips for Use To Change Projected Image Holding onto top mechanism - turn iPad® 90 degrees If swivel tension ever needs to be tighter, tighten this nut with 10mm wrench. Portrait Position Landscape Position NOTE: Sometimes when you rotate the iPad® your projected image does not rotate, in that case you need to tilt down the top mechanism to allow the iPad®...
Page 11
the Document Camera Stand - Tips for Use Using Dewey with iPad mini™ Slide the spacer into 1. Use the iPad mini™ spacer, and set the bottom lip to its minimum position. the provided slot Loosen the knob to slide the bottom lip into position and then tighten 2.
Page 12
the Document Camera Stand - Tips for Use Connecting to Your Projector To hold the VGA cable in For iPad mini™, iPad 2™ or newer only: place use provided VGA Strap - Tie the strap around the VGA Use Apple® VGA Adapter and a VGA cord (with two VGA male cable and then loop over the outlets) to connect projector to the iPad®.
Page 13
the Document Camera Stand - Tips for Use Basic Usage Tips Position stand in lowest height Place your iPad® into the stand. (See point 3 & 4) If your case has a flip cover, make sure it’s open to the side. Match the openings in the top mechanism with the Place your iPad®...
DCS1A the Document Camera Stand - Assembly Guide DCS2A For assistance, please contact us: Assembly Guide DCS1A_DCS2A_2014_E 1-800-267-8494 Check out our other products online at Email info@copernicused.com www.copernicused.com Have your packing slip ready for reference Dear Educator, Thank you for purchasing one of our products. I hope the assembly of your Dewey - the Document Camera Stand went well.