Table of Contents
Advertisement
IMPORTANT
Connection to the power supply must be carried out
in compliance with the regulations and provisions in
force in the country of use.
• Make sure the system power supply is arranged and able to
take the actual current load and that it is executed in a
workmanlike manner according to the regulations in force in
the country of use.
• The plug must be accessible after positioning the appliance
in the place of installation. Make sure the plug is not crushed
by the appliance. A damaged power cable can overheat and
catch fire or cause a short circuit.
• Make sure the machine power supply voltage specified on
the data plate matches the mains voltage.
• Make sure that the socket has an efficient ground contact.
CAUTION
GROUNDING
appliance must be grounded. In the event
of an electrical short circuit, grounding
reduces the risk of electric shock by
providing an escape wire for the electric
current. This appliance is equipped with a
cord having a grounding wire with a
grounding plug. The plug must be plugged
into an outlet that is properly installed and
grounded;
WARNING
Improper use of the grounding
can result in a risk of electric
shock.
Consult a qualified electrician or serviceman if the grounding
instructions are not completely understood, or if doubt exists
as to whether the appliance is properly grounded, and either:
1. If it is necessary to use an extension cord, use only a 3-
wire extension cord that has a 3-blade grounding plug,
and a 3-slot receptacle that will accept the plug on the
appliance. The marked rating of the extension cord shall
be equal to or greater than the electrical rating of the
appliance, or
2. Do not use an extension cord, if the power supply cord is
too short, have a qualified electrician or serviceman install
an outlet near the appliance.
WARNING
Earthing is mandatory, using a
green conductor.
I
NORMAL MACHINE USE
PRECAUTIONS FOR SAFE USE TO AVOID POSSIBLE
EXPOSURE TO EXCESSIVE MICROWAVE ENERGY
• Do not attempt to operate this appliance with the lid open -
lid operation can result in harmful exposure to microwave
energy.
• Do not place any object between the lid and the working top
or allow soil or cleaner residue to sealing surfaces.
• Do not operate the appliance if it is damaged. It is
particularly important that the appliance lid close properly
and that there is no damage to the: (1) lid (bent), (2) hinges
and latches (broken or loosened), (3) lid seals and sealing
surfaces.
• The appliance should not be adjusted or repaired by anyone
except properly qualified service personnel.
INSTRUCTIONS:
This
Whenever the power cable has to be replaced, call a technical
service agent and replace by original spare parts: only the
manufacturer of the appliance is authorized to supply the
replacement part and carry out disassembly and reassembly
of the components, directly or through Authorized Assistance
Centers.
IMPORTANT
Repair and maintenance work must be carried out
only by qualified personnel authorized by the
manufacturer.
Always install a main switch with thermal magnetic cut-out up
line of the appliance in order to be able to isolate it from the rest
of the system. Contact opening distance and maximum
leakage current must comply with current regulations
• Connect the mains plug to the mains socket only at the end
of the installation.
• Always use a correctly installed shockproof socket.
• Do not use multi-plug adapters and extension cables.
• Do not pull the mains cable to disconnect the appliance.
Always pull the mains plug.
• Do not touch the mains cable or the mains plug with wet
hands.
• The equipment must also be included in an equipotential
system, whose connection is made by means of screw "EQ"
(see "Installation diagram") indicated by the symbol
equipotential wire must have a section of at least 10 mm
H.8
Disposal of packing
The packing must be disposed of in compliance with the
current regulations in the country where the appliance is used.
All the packing materials are environmentally friendly.
They can be safely kept, recycled or burned in an appropriate
waste incineration plant. Recyclable plastic parts are marked
as follows:
Polyethylene
• Outer wrapping
• Instructions bag
Polypropylene
• Straps
• Top packaging panels
Polystyrene foam
• Corner protectors
The parts in wood and cardboard can be disposed of,
respecting the current regulations in the country where the
machine is used.
I.1
Characteristics of personnel trained for
normal machine use
The Customer must make sure the personnel for normal
machine use are adequately trained and skilled in their duties,
as well as ensuring their own safety and that of other persons.
The Customer must make sure his personnel have understood
the instructions received and in particular those regarding work
hygiene and safety in use of the machine.
I.2
Characteristics of personnel enabled to
operate on the machine
The Customer is responsible for ensuring that persons
assigned to the various duties:
• read and understand the manual;
. The
2
.
21
Hide quick links:
Advertisement
Table of Contents
