Page 2
This manual provides critical safety instructions on the proper setup, operation, maintenance, and service of this machine/tool. Save this document, refer to it often, and use it to instruct other operators. Failure to read, understand and follow the instructions in this manual may result in fire or serious personal injury—including amputation, electrocution, or death.
Machine Differences tech support, and it helps us determine if updated documentation is available for your machine. Models G0944 and G0944HEP are identical machines, with one exception. Model G0944HEP is equipped with a MERV-17 HEPA filter. The G0944 is not.
Become familiar with the names and locations of the controls and features shown below to better understand the instructions in this manual. Motor Inlet Wall Bracket Filter Cleaning Handle Canister Filter (G0944 Shown) To reduce your risk of serious injury, read this entire manual BEFORE using machine. Model G0944/G0944HEP (Mfd. Since 03/21)
Failure to do so could result in serious per- with respect and caution to decrease the sonal injury, damage to equipment, or poor risk of operator injury. If normal safety pre- work results. cautions are overlooked or ignored, serious personal injury may occur. Model G0944/G0944HEP (Mfd. Since 03/21)
G0944 Data Sheet MACHINE DATA SHEET Customer Service #: (570) 546-9663 · To Order Call: (800) 523-4777 · Fax #: (800) 438-5901 MODEL G0944 1‐1/2 HP WALL‐MOUNT DUST COLLECTOR WITH CANISTER FILTER Product Dimensions: Weight................................71 lbs. Width (side-to-side) x Depth (front-to-back) x Height............22-1/2 x 23-1/2 x 77-1/2 in.
Page 8
The information contained herein is deemed accurate as of 7/20/2021 and represents our most recent product specifications. Model G0944 PAGE 2 OF 2 Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. Model G0944/G0944HEP (Mfd. Since 03/21)
The information contained herein is deemed accurate as of 7/20/2021 and represents our most recent product specifications. Model G0944HEP PAGE 1 OF 2 Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. Model G0944/G0944HEP (Mfd. Since 03/21)
Page 10
The information contained herein is deemed accurate as of 7/20/2021 and represents our most recent product specifications. Model G0944HEP PAGE 2 OF 2 Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. Model G0944/G0944HEP (Mfd. Since 03/21)
Never operate under the influence of drugs or injury or blindness from flying particles. Everyday alcohol, when tired, or when distracted. eyeglasses are NOT approved safety glasses. Model G0944/G0944HEP (Mfd. Since 03/21)
Page 12
Make sure they are properly installed, you experience difficulties performing the intend- undamaged, and working correctly BEFORE ed operation, stop using the machine! Contact our operating machine. Technical Support at (570) 546-9663. -10- Model G0944/G0944HEP (Mfd. Since 03/21)
DO NOT place dust collector where it can what type of wood dust you will be exposed to in be exposed to rain or moisture, which creates a case of an allergic reaction. shock hazard and will reduce life of machine. -11- Model G0944/G0944HEP (Mfd. Since 03/21)
Page 15
Two-prong outlets do not meet the grounding requirements for this machine. Do not modify or use an adapter on the plug provided—if it will not fit the outlet, have a qualified electrician install the proper outlet with a verified ground. -13- Model G0944/G0944HEP (Mfd. Since 03/21)
IMPORTANT: Save all packaging materials until Collection Bag ..........1 you are completely satisfied with the machine and have resolved any issues between Grizzly or the Box 2 (Figure 5) shipping agent. You MUST have the original pack- G. Bag Clamp 15"..........1 aging to file a freight claim.
Hardware Recognition Chart USE THIS CHART TO MATCH UP HARDWARE DURING THE INVENTORY AND ASSEMBLY PROCESS. Flat Head Screw -15- Model G0944/G0944HEP (Mfd. Since 03/21)
" Minimum Side View Front View Power Minimum 3" Motor Cooling ⁄ " Air Gap Minimum ⁄ " Wall Keep Area Clear Wall Floor Floor ⁄ " ⁄ " Figure 6. Minimum working clearances. -16- Model G0944/G0944HEP (Mfd. Since 03/21)
(see Figure 9). Wall " Minimum Anchor Stud Lag Shield Anchor and Lag Screw Floor Figure 9. Typical fasteners for mounting dust Figure 7. Wall bracket position. collector bracket to masonry or concrete. -17- Model G0944/G0944HEP (Mfd. Since 03/21)
Page 20
Figure 11. Dust collector hung on wall bracket. Figure 10. Canister attached to dust collector Attach inlet adapter to dust collector inlet port and filter cleaning handle attached to canister. and secure adapter with 10-24 x ⁄ " flange screw. -18- Model G0944/G0944HEP (Mfd. Since 03/21)
To test remote control operation, press green remote button to turn motor ON, then press red remote button to turn motor OFF. — If the machine does not start or stop, verify batteries are correctly installed in remote. -19- Model G0944/G0944HEP (Mfd. Since 03/21)
The air flow test probe is located 1.5x duct diameter upstream from the air inlet. Test pipe length is a minimum of 10x duct tion lines. diameter. Figure 13. G0944 performance curve table and The Model G0944/G0944HEP works quite well as data. a point-of-use dust collector, or for collecting dust from up to two machines simultaneously.
External Ground Wire Internal Always guard against stat- Ground Wire ic electrical build up by Ground grounding all dust collec- Screw tion lines. Flex-Hose Figure 16. Flex-hose grounded to machine. -21- Model G0944/G0944HEP (Mfd. Since 03/21)
The purpose of this overview is to provide the nov- The spunbond polyester filter in the G0944 catch- ice machine operator with a basic understanding es 99.9% of 1-micron particles, and is pleated to...
Installing unapproved accessories may cause machine to malfunction, resulting in serious personal injury or machine damage. To reduce this risk, only install accessories recommended for this machine by Grizzly. T32555 T32168 NOTICE Refer to our website or latest catalog for additional recommended accessories.
Page 26
1", 2", 2.5", 3", 4", 5", and 6". Wall thickness is ⁄ ". Figure 22. Flexible clear dust hose. Figure 24. W1039 Universal Adapter. www.grizzly.com 1-800-523-4777 order online at or call -24- Model G0944/G0944HEP (Mfd. Since 03/21)
2. Motor fan rubbing on fan cover. 2. Fix/replace fan cover; replace loose/damaged fan. 3. Centrifugal switch at fault. 3. Replace. 4. Motor bearings at fault. 4. Test by rotating shaft; rotational grinding/loose shaft requires bearing replacement. -26- Model G0944/G0944HEP (Mfd. Since 03/21)
Page 29
2. Inlet cover seal loose/damaged. 2. Tighten all mounting and sealing points; use silicon to seal. -27- Model G0944/G0944HEP (Mfd. Since 03/21)
Technical Support at (570) 546-9663. The photos and diagrams included in this section are best viewed in color. You can view these pages in color at www.grizzly.com. -28- Model G0944/G0944HEP (Mfd. Since 03/21)
SECTION 10: PARTS We do our best to stock replacement parts when possible, but we cannot guarantee that all parts shown are available for purchase. Call (800) 523-4777 or visit www.grizzly.com/parts to check for availability. Main 28 29 36-4 36-1 36-2...
Page 33
END CAP 4" P0944044 CRANK HANDLE M10-1.5 X 14 P0944026 ALUMINUM IMPELLER 12-3/4" P0944045 LOCK NUT M10-1.5 P0944027 IMPELLER WASHER 1/4 BUY PARTS ONLINE AT GRIZZLY.COM! -31- Model G0944/G0944HEP (Mfd. Since 03/21) Scan QR code to visit our Parts Store.
Safety labels help reduce the risk of serious injury caused by machine hazards. If any label comes off or becomes unreadable, the owner of this machine MUST replace it in the original location before resuming operations. For replacements, contact (800) 523-4777 or www.grizzly.com. BUY PARTS ONLINE AT GRIZZLY.COM! -32- Model G0944/G0944HEP (Mfd.
WARRANTY & RETURNS Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance.
Need help?
Do you have a question about the G0944 and is the answer not in the manual?
Questions and answers