Advertisement
Quick Links
Advertisement
Related Manuals for RTA Techni Mobili RTA-8412L
Summary of Contents for RTA Techni Mobili RTA-8412L
- Page 1 MODEL RTA-8412L ASSEMBLY INSTRUCTIONS Thank you for purchasing our product REV.042021-1...
- Page 2 RTA-8412L Please read carefully the assembly instructions • before the installation. Do not discard this manual or any of the packaging • material until the unit has been completely assembled. Might require two people. •...
- Page 3 RTA-8412L Main Tabletop Right Tabletop Left Exterior panel Left Interior panel Right Interior panel Center-Left panel Center-Right panel Right Exterior panel Skirt panel for right cabinet Right-Top Shelf panel Skirt panel for left cabinet Left-Top Shelf panel Right-Bottom Shelf panel...
- Page 4 RTA-8412L MAIN PARTS LAYOUT (FOR REFERENCE) LIST OF HARDWARE, SCREWS AND FITTINGS Door Stopper PART QTY. ITEM Handle U Shape 2Pcs Long Wooden Pin 3Sets (96mm) M3.6x22mm Screw 60Pcs Short Wooden Pin 2 Pcs Door Hinge Cam Lock & 16Sets...
- Page 5 RTA-8412L ☛ This unit uses cam bolts and locks. The following explains how to use them. This is not an assembly step; it is a guide for when you are actually doing the assembly using this kind of hardware.
- Page 6 RTA-8412L ❼ ❶ ❽ ❷ ❸ ❾ ❹ ❿ ❺ ❻...
-
Page 7: Assembly Steps
RTA-8412L ASSEMBLY STEPS Install the short dowels 2 into all panels as shown. Use a wooden or light rubber STEP 1 hammer to avoid damage to the pins. Please pay attention to the correct holes to use as Hardware/Tools: other holes on the panels are intended for other hardware in other steps. - Page 8 RTA-8412L Install bolts 3 into panels A, B, S1 and T1 in the holes indicated in the illustration. Please STEP 3 pay attention to the correct holes to use as other holes on the panels are intended for other hardware, and attach the metal plates 18 to panel B using screws 7 as shown.
- Page 9 RTA-8412L For each set of slider 20, Separate the pieces according to their shape: STEP 5 - The Flat shaped will be used in the next step (2 pieces, both left and right). - The "L" shaped will be used until step 21 (2 pieces, left and right).
- Page 10 RTA-8412L Assemble the panel H to panel Q using screw 9 as shown. STEP 7 Hardware/Tools: ST5 x 40 (NOT INCLUDED) STEP 8 Assemble the panel E to panel Q using screws 9 as shown. Hardware/Tools: This illustration shows the...
- Page 11 RTA-8412L P.10 P.10 First assemble the panels L and N to panel E using screws 9, then join panels J STEP 9 to panel E by just pushing the dowels into the holes. Hardware/Tools: ST5 x 40 (NOT INCLUDED) This illustration shows the same parts from step 8, but viewed from a different angle (from the left).
- Page 12 RTA-8412L P.11 P.11 Assemble the panel G to panel P using screw 9 as shown. STEP 11 Hardware/Tools: ST5 x 40 (NOT INCLUDED) STEP 12 Assemble the panel D to panel P using screw 9 as shown. Hardware/Tools: ST5 x 40...
- Page 13 RTA-8412L P.12 P.12 First assemble the panels K and M to panel D using screws 9, then join panels I to panel STEP 13 D by just pushing the dowels into the holes. Hardware/Tools: ST5 x 40 (NOT INCLUDED) This illustration shows the same parts from step 12, but viewed from a different angle (from the right).
- Page 14 RTA-8412L P.13 P.13 With the help of another person, bring the sections assembled in steps 10 and 14 upright STEP 15 and place them oriented as shown. Then assemble panel H to panel G using screws 9. Then slide the panel V through the grooves of C and D, and W through the grooves of E Hardware/Tools: and F.
- Page 15 RTA-8412L P.14 P.14 First make sure that the back edge of the tabletop B aligns with the edge of the tabletop A, STEP 17 then using screws 7, and from underneath the unit, attach: Hardware/Tools: - The metal plate 18 from B to A.
- Page 16 RTA-8412L P.15 P.15 - Using cam locks 3, and as shown and explained in page 4, assemble: STEP 19 - The side panels S2 and S3 to front panel S1. - The side panels T2 and T3 to front panel T1.
- Page 17 RTA-8412L P.16 P.16 Place both drawers upside-down and assemble to their bottom the “L” shaped sliders using STEP 21 screws 7 as shown. Please note that the wheels go towards the back of the drawers and the sliders should Hardware/Tools: not protrude from the bottom, otherwise the drawers raise 1”...
- Page 18 RTA-8412L P.17 P.17 Install to the door R the Handle Set 14, and the Hinges 15 with screws 5 as shown. STEP 23 Hardware/Tools: ST4.5 x 13 (NOT INCLUDED) Place both drawers into the right cabinet as shown, then assemble the door R to the left...
- Page 19 RTA-8412L P.18 P.18 Cover all the screw heads with caps 11 as shown. STEP 25 Hardware/Tools: ALL DONE! Give yourself a nice pat on the back. You did a great job!
-
Page 20: Weight Limits
RTA-8412L P.19 P.19 AFTER THE ASSEMBLY IS DONE, PLEASE READ CAREFULLY THE FOLLOWING CARE AND MAINTENANCE WARNINGS: WEIGHT LIMITS 110 Lbs (50Kg ) 110 Lbs (50Kg) 11 Lbs (5Kg) 11 Lbs (5Kg) 11 Lbs (5Kg) 10 Lbs (4.5Kg) 10 Lbs (4.5Kg) 11 Lbs (5Kg) •... - Page 21 P.20 P.20 RTA-8412L...
- Page 22 P.21 P.21 RTA-8412L...
Need help?
Do you have a question about the Techni Mobili RTA-8412L and is the answer not in the manual?
Questions and answers