fantastic furniture Java Console Table Manual
Hide thumbs
Also See for Java Console Table:
- Manual (18 pages) ,
- Quick start manual (13 pages) ,
- Assembly instructions manual (7 pages)
Advertisement
Quick Links
Advertisement
Related Manuals for fantastic furniture Java Console Table
Summary of Contents for fantastic furniture Java Console Table
- Page 1 Version 1.0 Java Two People Console Table fantasticfurniture.com.au Required...
- Page 2 We’re thrilled you’ve chosen Fantastic Furniture to help create a home you’ll love! Love it? Share it! Fantastic buy! Share how it looks at home on Instagram for your chance to win a $250 Fantastic Furniture Gift Card! @fantasticfurniture fantasticfurniture.com.au Page 2...
-
Page 3: Assembly Checklist
Assembly Checklist Read through the instructions carefully Make sure you have all the required tools. before you begin. Never use power tools unless instructed. Unless instructed, do not fully tighten Identify and lay out all of the screws until the item is fully assembled. components before you begin assembly. -
Page 4: What You Need
What you need to assemble the product Other tools you need Flat Head Screwdriver; Phillips Head Screwdriver; Mallet Top Panel (P1) Side Panel Back Panel (P3) (P5) Side Panel Divider Panel (P3) (P4) Bottom Panel (P2) (P8) (P7) (P12) Drawer Back (P9) (P9) (P10) - Page 5 Hardware Pack 12 x Dowels ø8mm 4 x Felt Feet 2 x Handles 24 x Cam Bolts 12 x Large Cam (H3) (H5) (H4) (H1) Nuts (H2) 8 x Bolts 8 x Spring 4 x Screws 16mm 4 x Back Panel 12 x Flat Washers (H8) Washers (H10)
- Page 6 Step 1 (P12) You will need 4 x Felt Feet (H5) Attach 1 x felt foot (H5) onto each leg (P12) as shown. Step 2 Two People (P12) You will need (P2) Required 8 x Bolts 8 x Flat (H8) Washers (H9) 8 x Spring 1 x Allen Key...
- Page 7 Step 3 You will need 6 x Cam Bolts Phillips Head (H1) Screwdriver (P2) Screw 6 x cam bolts (H1) into bottom panel (P2), using a phillips head screwdriver. Step 4 You will need 6 x Cam Bolts Phillips Head (H1) Screwdriver (P1)
- Page 8 Step 5 Separate the slide runners (H19-2) and slide tracks (H19-1) from 4 x slides (H19) by following the steps below: You will need Extend the slide runner all the way out. Press down the plastic release lever on the slide and pull out the slide runner (H19-2) completely.
- Page 9 Step 6 Please fasten the screws through Note the position these holes for this step You will need of the rubber stopper H19-1 H19-1 6 x Screws 2 x Slide 12mm (H18) Tracks (H19-1) Phillips Head 4 x Dowels Screwdriver 30mm (H3) (P4) H19-1...
- Page 10 Step 7 (P3) You will need (P4) 6 x Large Cam Flat Head Nuts (H2) Screwdriver (P2) (P3) This is how a cam nut works..The head of the cam bolt goes into the open mouth of the cam nut. You then turn the cam nut so it tightens over Laminated...
- Page 11 Step 9 (P1) You will need (P3) (P4) 6 x Large Cam Flat Head Nuts (H2) Screwdriver (P3) Position top panel (P1) onto panels (P3 x 2, P4) as shown. Make sure the groove in top panel (P1) is on the same side as the back panel (P5).
- Page 12 Step 11 (P8) You will need (P7) 4 x Dowels Mallet ø6mm (H16) Insert 1 x dowel (H16) into each drawer side panel (P7, P8) as shown. Use a mallet to gently tap the dowels into place if needed. Step 12 You will need 12 x Cam Bolts Phillips Head...
- Page 13 Step 14 (P10) (P7) (P8) (P6) Slide drawer base (P10) into the grooves on panels (P6, P7, P8). Repeat this step for the other drawer assembly. Ensure the pre-drilled holes on drawer sides (P7, P8) Step 15 align with holes on back panel (P9), and the holes on back panel (P9) align with the holes on You will need...
- Page 14 Step 16 Please fasten the screws through these holes for this step. You will need H19-2 12 x Screws 4 x Slide H19-2 Runners (H19-2) 12mm (H18) Phillips Head (P8) Screwdriver H19-2 (P7) Attach 1 x slide runner (H19-2) to each drawer left side (P7) and drawer right side (P8) with 3 x screws (H18), using a phillips head screwdriver as shown.
- Page 15 Step 18 Move inner ball bearing track to front of slide track (H19-1). Gently insert drawer slide runner (H19-2) in between the ball bearing track. H19-2 H19-1 Position drawer so that slide runners (H19-2) align with slide tracks (H19-1) as shown. Gently push drawer into the closed position.
- Page 16 We strongly recommend Step 19 that this product is permanently fixed to the wall or other suitable surface. You will need (P1) 2 x Flat 2 x Screws Washers (H9) 25mm (H14) (P5) 2 x Wall Straps Phillips Head (H13) Screwdriver H14 H9 (P1)
-
Page 17: Job Complete
Step 21 Job complete! In the interest of our environment please dispose of all packaging thoughtfully. fantasticfurniture.com.au Page 17...