Related Manuals for Berbel Downline Infinity BKA 90 DLI
Summary of Contents for Berbel Downline Infinity BKA 90 DLI
- Page 1 Hob extractor fan Downline Infinity Operating and installation instructions for the models ƒ BKA 90 DLI 6006047_0...
- Page 2 Document information Symbol clarification - text ☞ Handling requirement Operating and installation instructions for: y Hob extractor fan BKA 90 DLI E00 y Listing y Original instructions. D Reference to another point in this document y Part of the product. y Copyright protected.
-
Page 3: Table Of Contents
Table of contents Safety information ......4 Operation of the hob ....27 Proper intended use . -
Page 4: Safety Information
Safety information Safety information Authorised target groups Electrical work only to be undertaken by qualified electricians per DIN VDE 0100. Requirements on qualified electricians: Proper intended use y Knowledge of the basics of electrics. y Knowledge of country-specific regulations and standards The device is designed for normal domestic cooking, frying (e.g. -
Page 5: General Safety Instructions
Safety information General safety instructions D WARNING! Hazard through a disregard of the operating and installation instructions! This manual contains important information for the safe handling of the device. Separate reference is made to possible hazards. ☞ Read through this manual thoroughly. ☞... -
Page 6: Product Information
Product information Product information In recirculated air mode, it is necessary to use the run-on function so that the device can remove the remaining odours. Using the run-on function increases the life of the filter filling. The filter filling must be replaced at regular Functional principle intervals. -
Page 7: Scope Of Delivery
Product information Scope of delivery 2.4.2 Accessory recirculating air kit DL BUF 2.4.1 Hob extractor fan A Powermover B Intake grate C Separator insert D Hob with fan housing and connection cable E Operating and installation instructions Depending on the operating mode, further accessories are required: y Recirculating air kit DL BUF –... -
Page 8: Accessory Recirculating Air Kit Dl Bur
Product information 2.4.3 Accessory recirculating air kit DL BUR 2.4.4 Accessory exhaust air kit DL A 150 mm conduit bend, 90° vertical B 150 mm elbow duct, 352 mm long C 150 mm shallow duct, 500 mm long D Height compensation plates, thickness 0.5/1.0/1.5/2.0 mm E 2x fastening base F 2x compression tape G Sealing strip... -
Page 9: Technical Data
Product information Technical data Front Rear Rear Front left left right right 2.5.1 Hob extractor fan Output external cooking 2300 W 2300 W 2300 W 2300 W zone BKA 90 DLI Output internal cooking – – 1100 W 1100 W zone 400 V ~ / Connection voltage 50/60 Hz Boost output... -
Page 10: Installation
Installation Installation Requirements for the installation location D WARNING! Safety instructions for installation Risk of death due to improper installation! Disregard of the ambient conditions can lead to hazardous situations, e.g. in the handling of electrical power or gas. D WARNING! ☞... -
Page 11: Requirements For Individual Operating Modes
Installation Requirements for the exhaust air ducting y The device must remain accessible at all times for (only for extracted air mode) maintenance work (e. g. with a removable rear panel or service cover). The space must be sufficiently large to allow for removal of the recirculated air filter. D WARNING! y During recirculated air mode sufficiently large ventilation Fire hazard and asphyxiation hazard due to improper... -
Page 12: Installation Procedure
Installation Installation procedure If accessories (e.g. wall box, window contact switch) are required for the installation: Short overview: Observe the instructions for the accessories. 1. Preparation for installation ☞ Ensure that the accessories are correctly installed and 2. Unpack the device ready for connection. -
Page 13: Check The Dimensions
Installation 3.5.3 Check the dimensions Counter-top installation To determine the dimensions of the hob, refer to the order documents. Flush installation ≥ 5 Width (a) 880 + 2 mm Cutaway Depth (b) 530 + 2 mm Work top Height (z) >... -
Page 14: Install The Hob
Installation 3.5.4 Install the hob D WARNING! Danger of injuries through improper handling! Installation of the device requires a great deal of physical exertion due to its size and weight. If the device falls down, serious injuries are possible. ☞ Install the device with two persons. ☞... - Page 15 Installation ☞ Fit the Powermover on the intake grate. ☞ Seal the cut surface of the work tip with suitable material (heat resistant to 75 °C - e.g. special paint, silicone rubber or cast resin). For the material used, the worktop manufacturer’s instructions must be followed.
-
Page 16: Install Recirculating Air Kit Dl Buf
Installation 3.5.5 Install recirculating air kit DL BUF Installation variant for recirculated air mode with active carbon filter. The instructions for installation variants with blow-out grate kit must be observed. ☞ Align the recirculated air filter with the flap device to the access side. -
Page 17: Install Recirculating Air Kit Dl Bur
Installation 3.5.6 Install recirculating air kit DL BUR Installation variant for recirculated air mode with recirculated air filter permalyt. The instructions for installation variants with blow-out grate kit must be observed. By trimming, it is possible to align the shallow duct with the spacing between the connections: y Between the fan‘s housing and circulating air bend with deep base cabinets. - Page 18 Installation ☞ Adjust the recirculated air filter to the appropriate height: ☞ Insert the shallow duct sections in the circulating air y Height-adjustability of at least 100 mm is necessary, bend. in order to install the shallow duct sections afterwards. ☞...
-
Page 19: Install Exhaust Air Kit Dl
Installation 3.5.7 Install exhaust air kit DL Installation variant for extracted air mode. By trimming, it is possible to align the shallow duct with the spacing between the connections: y Between the fan housing and conduit bend with deep base cabinets. y Between the conduit bend and elbow duct with high base cabinets. -
Page 20: Connect Accessories
Installation 3.5.8 Connect accessories Wall box y The wall box is closed when the control contacts are Available accessories are connected depending on the open. installation situation, e.g.: y The wall box is open when the control contacts are y Wall box closed. -
Page 21: Establish Electrical Power Supply
Installation 3.5.9 Establish electrical power supply 3.5.10 Check and carry out commissioning D WARNING! D ATTENTION! Risk of death due to electric shock! Risk of disruptions due to moisture in the device! Touching live parts can cause an electric shock, burns or If the device is moved from a cold environment into a hot death. -
Page 22: Operation
Operation Operation y Sharp and hard objects (e.g. pot edges) can damage the glass on the hob due to impact or falling. y Do not use magnetic objects (e.g. data carriers, credit cards) near the device. The function of these objects can Safety instructions for operation be impaired. -
Page 23: Cooking With Induction
Operation Cooking with induction In comparison to other types of hob (e.g. radiant heating or gas), there are a few peculiarities that must be observed when using an induction hob. D WARNING! Risk of burns on hot parts! The heating time can be very short with induction hobs. The hob, cookware and the prepared food can become quickly hot. -
Page 24: Control Panel
Operation Control panel Function keys for the entire hob The device is controlled via the control panel. The control panel is located centrally between the cooking zones. Menu Extraction operating mode Grill Head chef A Operation of the front left cooking zone Automatic pot recognition B Operation of the rear left cooking zone C Operation of the rear right cooking zone... - Page 25 Operation Function keys for the individual cooking zones Function keys for extraction 3x 7 segment display 7-segment display of extraction 7-segment display of the cooking zone Previous power level Menu Next power level Slider No function Cooking zone - count down Filter filling indicator, window contact switch Cooking zone - count up Run-on function...
-
Page 26: General Operation Of The Device
Operation General operation of the device The cooking zone is selected with the corresponding 7-segment display or via the D WARNING! automatic pot recognition. ☞ Touch the 7-segment display. Risk of burns on hot parts! y The 7-segment display lights up brightly. The hob, cookware and the prepared foot can become very y Further entries only apply for the selected hot while working with the device. -
Page 27: Operation Of The Hob
Operation Operation of the hob Manual mode The setting of the fan power takes place manually. The connection between the selection of the cooking zone level and fan power selection is severed. Semi-automatic mode When the hob is switched on and a cooking Additional functions are available via the hob menu button. -
Page 28: Head Chef Function
Operation 4.5.3 Head chef function 4.5.5 “Pot speed test” function Function for adjustment of cooking zones to a stored cooking Function for determining whether the cookware is suitable level. Display of the pot recognition is deactivated with this for use with the induction hob. function. -
Page 29: Hob - Count Down Function
Operation 4.5.6 Hob - count down function 4.5.8 Pause function Function for individual time measurement from 1 second to Function for interruption of a cooking process with saved 99 minutes. The function is independent of the activities on settings. the hob. ☞... -
Page 30: Volume Function
Operation 4.5.11 Volume function Operation of the cooking zones Function for adjusting the volume of acoustic signals. ☞ Touch the symbol. y The 7-segment display of the extraction shows the set value (e.g. volume 2). Additional functions are available via the cooking zones menu button. -
Page 31: Cooking Zone - Count Up Function
Operation 4.6.2 Cooking zone - count up function 4.6.5 Boost function Function for individual time measurement for each cooking Function for heating up the cooking zone quickly. zone from 1 second to 999 minutes. ☞ Touch the symbol to start the power level ☞... -
Page 32: Cooking Zone Size Function
Operation Extraction operation If the function is in use, the cookware may not be automatically detected (e.g. because the size is insufficient or the material does not optimally conduct). ☞ Touch the 7-segment display of both left cooking zones at the same time for 3 seconds. -
Page 33: Filter Filling Indicator
Operation 4.7.1 Filter filling indicator 4.7.3 Run-on function The device has a check indicator in order to remind the The device comes with a run-on function. If this function operator to change the filter filling. If no recirculated air filter is used, the device will operate for a further 10 minutes at is used, the control indicator does not have any meaning. -
Page 34: Cleaning
Cleaning Cleaning Cleaning procedures If sugar, plastic, aluminium foil or similar materials come into contact with the hot hob, these materials must be removed Safety instructions for cleaning immediately: ☞ Turn off the device. ☞ Remove the materials while they are still hot. There is a D WARNING! risk of burns because the hob is hot. - Page 35 Cleaning The control panel can be locked for 20 seconds with the cleaning function in order to prevent unintended activation. D “4.5.12 Cleaning function” (page 30). ☞ Clean the hob and the Powermover with a damp cloth or with special products for glass ceramic. ☞...
-
Page 36: Maintenance
Maintenance Maintenance Maintenance Replacing filter filling (with recirculated air mode) Odours are trapped in the filter filling in the recirculated air Safety instructions for maintenance filter. The odour-free, cleaned room air is fed back into the room. D WARNING! Recirculated air filters are maintenance-free for up to two Hazard through a disregard of the maintenance years. - Page 37 Maintenance Filter cartridge ☞ Remove the filter cartridge. ☞ Unscrew the screws on the bottom of the filter cartridge. Horizontal recirculated air filter (with installation variants with ☞ Open the filter cartridge by removing the filter bottom. blow-out grate kit) ☞...
-
Page 38: Fault Rectification
Maintenance Fault rectification Odours occur during operation. y The filter filling is used up. Possible faults are described below: ☞ Change the filter filling. Description of the fault. D “Replacing filter filling (with recirculated air mode)” y Possible cause. (page 36). ☞... - Page 39 Maintenance The control panels do not respond, the displays on all control The display on the control panel shows “U401”. y The power supply is too low (< 160 V). panels show “L”. ☞ De-energise the device. ☞ Switch on the device again. If a fault persists: ☞...
-
Page 40: Disassembly
Disassembly Disassembly D WARNING! Danger of injuries through improper handling! Disassembly of the device requires a great deal of physical exertion due to its size and weight. If the device falls down, serious injuries are possible. ☞ Disassemble the device with two persons. ☞... -
Page 41: Disposal
Disposal Disposal Dispose of the device D ATTENTION! Dispose of packaging Risk of environmental damage due to improper disposal of the device! D ATTENTION! The device is subject to the European Directive 2012/19/EU and should not be disposed of with household waste. Risk of environmental damage due to improper disposal ☞... -
Page 42: Annex
BKA 90 DLI E00 with exhaust air kit DL Energy efficiency index (EEI) – – 43.7 EEI Hood Class – – FDE Hood – – 34.1 berbel BKA 90 DLI E00 FDE Hood Class – – LE Hood – – – LE Hood Class – –... -
Page 43: Contact
Annex Contact If you have any questions or suggestions, please select from the following options: Post: berbel Ablufttechnik GmbH Sandkampstraße 100 D-48432 Rheine Telephone: +49 (0) 5971 / 80 80 9 - 0 Mon to Thu 8:00 – 17:30 hrs and Fri 8:00 –... - Page 44 6006047_0 02.09.2021...