Table of Contents
Advertisement
System installation shall only be undertaken by qualified
technicians holding a training certificate issued by an
authorized distributor. The manufacturer cannot be held
responsible for any damage or consequences related to the
improper or incorrect use of this product.
1.
Control panel architecture
• The JA-82KRC is a basic configuration of the JA-82K
control panel. The JA-82K main board provides building-
block-like modularity which allows functional extensions to
be made by simply plugging-in the required modules. The
basic JA-82K provides 4 wired inputs. The following
additional modules can be plugged-in:
o JA-82R – a radio module, providing 50 wireless inputs
(addresses). This module makes it possible that up to 50
wireless devices of the JA-8x can be enrolled.
o JA-82C – a wired input extension module. This module
provides 10 additional wired inputs, thus extending the
total capacity to 14 wired inputs (addresses 05 to 14).
o JA-80Y – a GSM communicator which allows alarm
reporting, ARC (alarm receiving centre) communication
via GSM and remote access via a phone keypad or via
the Internet (using the GSMLink web application).
o JA-80V – a LAN / PSTN line communicator which allows
alarm reporting via a fixed line, ARC communication via
LAN (Ethernet) and remote access via a phone keypad
or via the Internet (using the GSMLink web application).
o JA-80X – a phone-line voice communicator which allows
alarm voice-reporting, ARC communication and remote
access via a telephone keypad. This module can be used
in combination with JA-80Y.
• Depending on the type, a device can be connected either to
a wired input or to a wireless input (then the device is said
to be wirelessly connected or enrolled). Both wired and
wireless inputs are identified by addresses (positions). The
address range is 01 to 04 or 01 to 14 for wired inputs and
01 to 50 for wireless inputs.
Installation manual: OASiS security system JA-82KRC
+U
14
13
12
11
10
RESET
09
08
07
06
05
+U
ON
OFF
1 2 3 4
o The control panel does not allow for the simultaneous
connection of both a wired and a wireless input to the
same address. Connecting to a wired input automatically
disables the wireless input of the same address.
o Other hard-wired inputs are provided by some wireless
devices, such as keypads, door detectors, and PIR
movement detectors.
1.1.
Main features
• When triggered, a detector (or any other device connected
to the control panel) sends a so-called natural signal which
reflects the device type and thus primarily dictates what the
reaction of the control panel should be. E.g. the natural
signal of a door contact or PIR detector can be an instant or
delayed alarm which is selectable by a DIP switch inside the
detector. A keyfob, for instance, sends signals for set (arm),
unset (disarm) and panic.
o The control panel is factory-set to perform natural
reactions according to the signals sent from connected
devices. By programming the addresses of the devices in
the control panel, it is possible to define how the control
panel reacts to individual devices. E.g. a door detector
assigned to address 15 could trigger a panic reaction,
and a keyfob button using address 24 could cause a fire
reaction etc.
• Connected devices can be assigned to 3 sections: A, B or
C. Assignments to sections either have an effect when
partial setting is used e.g. only A is set, AB is set, or ABC is
set (which, for example, would be suitable for homes where
A could mean afternoon setting, AB night setting and ABC
total setting), or if the system was split into two independent
partitions A and B, with a common section C. In the second
case, each A or B section can be set individually, and C is
automatically set when both A and B have been set by
users. This would be suitable for two independent families in
a single house, or two companies in one building.
3 / 21
Antenna connection
Radio module
LEDs
SIM card
Communicator
Main board
Antenna
Cover tamper switch
Wired input module
Transformer
Input balancing
switches
Mains fuse
Back-up battery
GSM antenna
Digital bus connector
MKH51100_OS2
Advertisement
Table of Contents
