Table of Contents
Advertisement
Contents:
1.
Control panel architecture .......................................3
1.1.
Main features .......................................................................3
1.1.1.
Modes ...............................................................................4
1.2.
Optional system configurations............................................4
2.
Installation .................................................................4
2.1.
Power inlet ...........................................................................4
3.
Control panel memory unit ......................................4
4.
Control panel connectors and terminals ................5
5.
Wired keypad connection.........................................5
6.
Back-up battery .........................................................6
7.
7.1.
Wireless keypad enrollment.................................................6
8.
Language selection of the keypad ..........................6
9.
Resetting the control panel......................................6
10. Closing the control panel cover ..............................7
11. Enrolling wireless devices .......................................7
11.1.
Installing wireless devices ...................................................7
11.2.
Enrolling wireless devices to the control panel ....................7
11.3.
Testing enrolled devices ......................................................7
11.4.
Measuring signal strength....................................................7
11.5.
Erasing enrolled devices......................................................8
11.6.
Enrolling the control panel to UC and AC modules .............8
12. Control panel programming.....................................8
12.1.
Control panel programming sequences...............................8
12.2.
Exit delay time ...................................................................11
12.3.
Entrance delay time ...........................................................11
12.4.
Alarm duration time............................................................11
12.5.
PGX and PGY functions ....................................................11
12.6.
12.7.
Radio interference indication .............................................11
12.8.
Radio communications supervision ...................................11
12.9.
RESET enabled .................................................................12
control ................................................................................12
12.11. Master code reset ..............................................................12
control panel ......................................................................12
12.13. Setting (Arming) without an access code ..........................12
12.14. Triggered-detector indication .............................................12
12.15. Confirmation of intruder alarms .........................................12
12.16. Exit delay beeps ................................................................13
12.17. Exit delay beeps while partially setting (arming)................13
12.18. Entrance delay beeps ........................................................13
12.19. Setting (arming) confirmation by wired-siren chirp ............13
12.20. Sirens always sound during audible alarms ......................13
Installation manual: OASiS security system JA-82KRC
12.21. Wireless siren alarm enabled (IW and EW) ...................... 13
12.22. Auto-bypass user approval via the ∗ key........................... 13
12.23. Final-door detectors........................................................... 13
12.24. Partial setting (arming) or system splitting ........................ 14
12.25. Automatic summer time (daylight saving time).................. 14
triggered tamper sensors................................................... 14
12.27. Operating the PG outputs using ∗8 and ∗9 ....................... 14
12.28. Permanent alarm status display for a set system.............. 15
12.29. Tamper alarm if unset........................................................ 15
12.30. Recording PG output activation to memory....................... 15
12.31. Engineer reset ................................................................... 15
12.32. Annual check notification................................................... 15
12.33. Only single alarm indication............................................... 15
12.34. Setting (arming) by service code ....................................... 15
12.35. Audible panic alarm ........................................................... 15
12.36. Higher control-panel receiver-sensitivity ........................... 16
12.37. Access by code plus card.................................................. 16
12.38. Audible 24 hour intruder alarm .......................................... 16
12.40. Device reactions and section assignment ......................... 16
12.41. Code/card reactions and section assignment ................... 17
12.42. Enrollment by keying in production codes ......................... 17
12.43. Automatic setting/unsetting schedule................................ 17
12.44. Changing the service code. ............................................... 17
12.45. Go to maintenance mode .................................................. 18
12.46. Setting the internal clock ................................................... 18
12.47. Editing keypad text ............................................................ 18
13. Operating the system............................................. 18
13.1.
The system keypad ........................................................... 18
13.1.1.
Keypad indicators: .......................................................... 18
13.1.2.
LCD display..................................................................... 18
13.1.3.
Keypad display sleep-mode............................................ 18
13.1.4.
Keys ................................................................................ 18
Functions beginning with the ∗ key ................................ 19
13.1.5.
13.2.
Programming access codes and cards ............................. 19
13.2.1.
Programming access codes and cards........................... 19
13.3.
13.4.
Maintenance Mode ............................................................ 20
13.4.1.
13.4.2.
Bypassing devices .......................................................... 20
13.4.3.
Protecting a car near the system .................................... 20
15. Basic guidance for installers ................................ 21
16. Trouble-shooting .................................................... 21
17. Control panel technical specifications................. 21
2 / 21
MKH51100_OS2
Advertisement
Table of Contents
