BRP Sea-Doo MOVE Series Operator's Manual page 35

M M A A I I N N T T E E N N A A N N C C E E A A N N D D I I N N S S P P E E C C T T I I O O N N P P R R O O C C E E D D U U R R E E S S
This section includes instructions for
basic maintenance procedures. If you
have the necessary mechanical skills
and the required tools, you can per-
form these procedures. If not, see
your authorized Sea-Doo dealer.
W W A A R R N N I I N N G G
T T o o r r q q u u e e w w r r e e n n c c h h t t i i g g h h t t e e n n i i n n g g s s p p e e c c i i f f i i - -
c c a a t t i i o o n n s s m m u u s s t t b b e e s s t t r r i i c c t t l l y y a a d d h h e e r r e e d d
t t o o . .
L L o o c c k k i i n n g g d d e e v v i i c c e e s s , , w w h h e e n n r r e e m m o o v v e e d d
( ( e e . . g g . . : : l l o o c c k k i i n n g g t t a a b b s s , , e e l l a a s s t t i i c c s s t t o o p p
n n u u t t s s , , c c o o t t t t e e r r p p i i n n s s , , e e t t c c . . ) ) , , m m u u s s t t b b e e
r r e e p p l l a a c c e e d d . .
Hoses, cables or locking ties removed
during a procedure must be rein-
stalled as per factory standards.
T T o o n n g g u u e e S S a a f f e e t t y y C C a a b b l l e e
T T o o n n g g u u e e S S a a f f e e t t y y C C a a b b l l e e I I n n s s p p e e c c t t i i o o n n
Inspect for damage.
Discontinue use and contact an au-
thorized Sea-Doo dealer if cable or its
liner damage is found.
W W A A R R N N I I N N G G
D D o o n n o o t t u u s s e e t t h h e e t t r r a a i i l l e e r r i i f f s s a a f f e e t t y y c c a a - -
b b l l e e s s a a r r e e d d a a m m a a g g e e d d . .
C C o o u u p p l l e e r r
C C o o u u p p l l e e r r I I n n s s p p e e c c t t i i o o n n a a n n d d L L u u b b r r i i c c a a t t i i o o n n
Check locking mechanism operation.
Check ball socket, ball clamp and lock
mechanism for wear or damage.
Apply a thin coat of multipurpose
grease to the inner surface of the ball
socket.
Apply light oil to the pivot and sliding
surface of the lock mechanism.
T T i i r r e e s s
T T i i r r e e P P r r e e s s s s u u r r e e
Check tire pressure. Tire pressure
must be checked while the tire is cold.
N N O O T T E E : :
Do not check the tire pressure imme-
diately after towing the trailer. Allow at
least three hours for a tire to cool
down, if the trailer has been towed for
as much as 1.6 km (1 mi).
The required pressure varies accord-
ing to the trailer model. Refer to
Specifications .
T T i i r r e e I I n n s s p p e e c c t t i i o o n n
Replace the tire before towing the
trailer if the tire tread has less than 1.6
mm (1/16 in) depth or if the built-in
wear indicator bars are visible and
flush with the remainder of the tire
tread.
Always replace a tire with one of the
same dimensions and load limit.
Inspect both sidewalls of each tire for
any bubble, cut or bulge; and replace
a damaged tire before towing the
trailer.
W W A A R R N N I I N N G G
A A b b u u b b b b l l e e , , c c u u t t o o r r b b u u l l g g e e i i n n t t h h e e s s i i d d e e - -
w w a a l l l l c c a a n n r r e e s s u u l l t t i i n n a a t t i i r r e e b b l l o o w w o o u u t t
a a n n d d l l o o s s s s o o f f c c o o n n t t r r o o l l . .
W W h h e e e e l l s s
W W h h e e e e l l I I n n s s p p e e c c t t i i o o n n
Check wheel for cracks, bumps or oth-
er damages.
required.
H H u u b b s s , , b b e e a a r r i i n n g g a a n n d d s s e e a a l l s s
W W h h e e e e l l B B e e a a r r i i n n g g I I n n s s p p e e c c t t i i o o n n
Install a jack under the axle and raise
until the tire gets off the ground. Push
and pull the wheel from the upper
Replace wheel as
35