Page 1
ProSource Packaging, Inc. 14911 Stuebner Airline Suite A Houston, TX 77069 800-203-0233 www.Machine-Solution.com Operating Instructions and Parts Manual DC-1100VX Series Dust Collectors Now with DC-1100VX with Bag Filter Kit DC-1100VX with Canister Kit WALTER MEIER (Manufacturing) Inc. 427 New Sanford Road LaVergne, Tennessee 37086 Part No.
Walter Meier is consistently adding new products to the line. For complete, up-to-date product information, check with your local Walter Meier distributor, or visit waltermeier.com. WARRANTY JET products carry a limited warranty which varies in duration based upon the product (MW = Metalworking, WW = Woodworking). WHAT IS COVERED? This warranty covers any defects in workmanship or materials subject to the exceptions stated below.
Table of Contents Warranty and Service ..........................2 Table of Contents ............................3 Warnings ..............................4 Introduction ...............................5 Specifications ............................6 Unpacking ..............................7 Shipping Content ............................7 Base Unit ...............................7 Canister Filter Kit ............................8 30-Micron Bag Filter Kit...........................8 5-Micron Bag Filter Kit ..........................8 Base Unit Assembly ...........................9 Base ..............................9 Motor and Fan Assembly ........................9 Connector Housing ..........................9...
Warnings 1. Read and understand the entire owner's manual before attempting assembly or operation. 2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with all of these warnings may cause serious injury. 3.
20. Make your workshop child proof with padlocks, master switches or by removing starter keys. 21. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are careless acts that can result in serious injury. 22. Do not use the dust collector for anything except wood dust. Materials such as liquids, metal shavings, metal dust, screws, glass, plastic or rock can cause sparks and/or damage when coming into contact with any part of the dust collector.
Specifications DC-1100VX-BK (Base Machine with 30 Micron Filter Bag Kit) ............708657K DC-1100VX-5M (Base Machine with 5 Micron Filter Bag Kit) ............708658K DC-1100VX-CK (Base Machine with Canister Filter Kit)..............708659K Base Machine (All Models) Model ..........................DC-1100VX Stock Number for Base Machine only ..................708657 Impeller Diameter ..........................
Unpacking Shipping Content Base Unit The table below lists the shipping cartons that are included with the models of the DC-1100VX Dust (SN 708657) Collector. 1 – Housing (A) 1. Locate your particular model and verify that you 2 – Hose Clamps (B) have received all of the correct cartons.
Base Unit Assembly Base 1. Install four casters to the underside of the base as pictured in Fig. 2. Referring to Figure 1: 2. Thread the hex nut (B) onto the caster shaft. Then slide the lock washer (A) over the caster shaft. Thread the caster shaft into the threaded hole on the underside of the base, turn until snug.
6. Install the housing (A, Fig. 5) to two support legs (B, Fig. 5) using four M8 x 16 hex cap bolts, eight M8 flat washers, and four M8 hex nuts (C, Fig. 5). Be sure hose opening faces fan housing. Note: For filter bag models only –...
Filter Bag Kit Assembly If you purchased a DC-1100VX-BK, or DC-1100VX- 5M Dust Collector, this section describes the assembly and installation of the contents of the Filter Bag Kit (SN 708636F or 708636MF). Filter Bag Installation Referring to Figure 8: 1.
Canister Kit Assembly purchased Model DC-1100VX-CK Dust Collector, this section describes the assembly and installation of the contents of the Canister Kit (SN 708639B). Canister Filter 1. Mount the handle onto the canister filter with two M10 hex nuts, two M10 flat washers, and a M10 lock washer (Figure 10).
Electrical Connections Dust Collector RF Remote Power Control (Optional) All electrical connections must done qualified The DC-RC Remote Power Control (Figure 14) electrician. All adjustments or repairs must be should be used for activating Dust Collection units done with the dust collector disconnected from powered by 115V only up to 1-1/2HP.
Changing Operating Frequency Installing the DC-RC Remote Power Control (Optional Accessory) If several devices are controlled by the same type remote control unit, each remote control unit can be The DC-RC Remote Power Control unit can be set to operate at its’ own unique operating frequency placed anywhere for convenience and portability if as follows: used to control other machines or it can be mounted...
Contact your Turn the bag inside out and clean. nearest JET distributor for the full line of JET Dust Turn the bag outside in and insert into the Collector Hoses and Accessories. Customize your housing.
Parts List – DC-1100VX Dust Collectors Ordering Replacement Parts To order parts or reach our service department, call 800-274-6848, Monday through Friday (see our website for business hours, www.waltermeier.com). Having the Model Number and Serial Number of your machine available when you call will allow us to serve you quickly and accurately.
Page 18
Index No. Part No. Description Size ....DC1200-53 ....Grounding Label (not shown)................1 ....DC1200-54 ....Direction Label (not shown) ................1 ....DC1100VX-ID..I.D. Label (not shown) ..................1 ....DC1100-HP .....Hardware Package for Base Unit ..............1 ....DC1100-HP2 ...Hardware Package for Cone Assembly ............1 ....