Hitachi WJ200-007MF Manual page 15

Code Function Name
b021
Overload restriction operation mode
b221 Overload restriction operation mode, 2nd motor
b022 Overload restriction level setting
b222 Overload restriction level setting, 2nd motor
b023
Deceleration rate at overload restriction
b223 Overload restriction operation mode, 2nd motor
b024 Overload restriction operation mode 2
b025 Overload restriction level 2 setting
b026
Deceleration rate 2 at overload restriction
b027 OC suppression selection
b028 Current level of active freq. matching restart setting
b029 Deceleration rate of frequency matching restart setting
b030 Start freq. to be used in case of active freq. Matching restart 00 (frequency at the last shutoff) / 01 (maximum frequency) / 02 (set frequency)
b031 Software lock mode selection
b033 Motor cable length parameter
b034 Run / power ON warning time
b035 Rotation direction restriction
b036 Reduced voltage start selection
b037 Function code display restriction
b038 Initial-screen selection
b039 Automatic user parameter setting
b040 Torque limit selection
b041 – b044 Torque limit (1) – (4)
b045 Torque LAD STOP selection
b046 Reverse run protection
b049 Dual Rating Selection
b050 Selection of the nonstop operation
b051 Nonstop operation start voltage setting
b052 OV-LAD Stop level of nonstop operation setting
b053 Deceleration time of nonstop operation setting
b054 Frequency width of quick deceleration setting
b060 Maximum-limit level of window comparators O
b061
Minimum-limit level of window comparators O
b062 Hysteresis width of window comparators O
b063 Maximum-limit level of window comparators OI
b064 Minimum-limit level of window comparators OI
b065 Hysteresis width of window comparator (OI)
b070 Operation level at O disconnection
b071
Operation level at OI disconnection
b075 Ambient temperature
b078 Watt-hour reset
b079 Watt-hour display gain setting
b082 Start frequency adjustment
b083 Carrier frequency setting
b084
Initialization mode (parameters or trip history)
b085 Country for initialization
b086 Frequency scaling conversion factor
b087 STOP key enable
Setting Range
00 (disabled) / 01 (enabled during acceleration and constant-speed operation) /
02 (enabled during constant-speed operation) /
03 (enabled during acceleration and constant-speed operation [speed increase at regeneration])
Set a level between 20% and 200% / 150% for the rated inverter current [A] (CT / VT)
0.1 to 999.9 / 1000. to 3000. [s]
0.1 to 999.9 / 1000. to 3000. [s]
00 (disabled) / 01 (enabled during acceleration and constant-speed operation)/
02 (enabled during constant-speed operation) /
03 (enabled during acceleration and constant-speed operation [speed increase at regeneration])
Set a level between 20% and 200% / 150% for the rated inverter current [A] (CT / VT)
0.1 to 999.9 / 1000. to 3000. [s]
00 (disabled) / 01 (enabled)
Set a level between 20% and 200% / 150% for the rated inverter current [A] (CT / VT)
0.1 to 999.9 / 1000. to 3000. [s]
00 (all parameters except b031 are locked when [SFT] terminal is ON) /
01 (all parameters except b031 and output frequency F001 are locked when [SFT] terminal is ON) /
02 (all parameters except b031 are locked) /
03 (all parameters except b031 and output frequency F001 are locked) /
10 (High level access including b031)
5 to 20
0 to 9999. (0 to 99990 [hr ]) / 1000 to 6553 (100000 to 655350 [hr ])
00 (Enable for both dir) / 01 (Enable for forward only) / 02 (Enable for reverse only)
0 (minimum reduced voltage start time) to 255 (maximum reduced voltage start time)
0 (full display) / 1 (function-specific display) / 2 (user setting) /
3 (data comparison display) / 4 (basic display) / 5 (monitor display)
000 (Func. code that SET key pressed last displayed) /
001 to 060 (d001 to d060) / 201 (F001) /
202 (Screen displayed when the STR key was pressed last)
00 (disabled) / 01 (enabled)
00 (quadrant-specific setting) / 01 (switching by terminal) / 02 (O input)
0 to 200 [%] / no
00 (disabled) / 01 (enabled)
00 (disabled) / 01 (enabled)
00 (CT mode) / 01 (VT mode)
[1-phase 100V class is only with CT]
00 (disabled) / 01 (enabled) /
02 (nonstop operation at momentary power failure [no restoration]) /
03 (nonstop operation at momentary power failure [restoration to be done])
0.0 to 999.9 / 1000. [V]
0.0 to 999.9 / 1000. [V]
0.1 to 999.9 / 1000. to 3600. [s]
0.00 to 10.00 [Hz]
0 to 100 [%]
0 to 100 [%]
0 to 10 [%]
0 to 100 [%]
0 to 100 [%]
0 to 10 [%]
0 to 100 [%] / no
0 to 100 [%] / no
-10 to 50 [ º C]
00 (OFF) / 01 (ON)
1 to 1000
0.10 to 9.99 [Hz] ( to 200Hz)
2.0 to 15.0 [kHz]
00 (disabled) / 01 (clearing the trip history) / 02 (initializing the data) /
03 (clearing the trip history and initializing the data) /
04 (clearing the trip history and initializing the data and EzSQ program)
00 / 01
0.01 to 99.99
00 (enabled) /
01 (disabled) /
02 (disabled only stop)
[ ○ = Allowed × = Not parmitted]
Setting During Change During
Default
Operation Operation
Setting
(allowed or not) (allowed or not)
× 01
○
× 01
○
×
○
150% of
Rated current
×
○
× 1.0
○
× 1.0
○
× 01
○
150% of
×
○
Rated current
× 1.0
○
× 01
○
Rated current
×
○
of inverter
× 0.5
○
× 00
○
× 01
○
10
○ ○
× 0
○
× × 00
× 2
○
× 04
○
× 001
○
× 00
○
× 00
○
× 200
○
× 00
○
× 01
○
× × 00
× × 00
× × 220 / 440
× × 360 / 720
× × 1.00
× × 0.00
100
○ ○
0
○ ○
0
○ ○
100
○ ○
0
○ ○
0
○ ○
× no
○
× no
○
40
○ ○
00
○ ○
1
○ ○
× 0.50
○
× 2.0
○
× × 00
× × 00
1.00
○ ○
× 00
○
15