Page of 15

Hitachi WJ200 Series Software Manual

115vif-din 115 vac input interface board for crane & hoist pendant applications.
Hide thumbs
115VIF-DIN
115 VAC Input Interface Board
Instruction & Software Manual
For Crane & Hoist Pendant Applications
NOTE: REFER ALSO TO WJ200 OR SJ700 SERIES INSTRUCTION MANUAL
Manual Number: HAL1055D
January 2013
• WJ200 Series
• SJ700 Series
Hitachi America, Ltd.
After reading this manual,
keep it handy for future reference.

   Summary of Contents for Hitachi WJ200 Series

  • Page 1

    For Crane & Hoist Pendant Applications • WJ200 Series • SJ700 Series NOTE: REFER ALSO TO WJ200 OR SJ700 SERIES INSTRUCTION MANUAL Manual Number: HAL1055D After reading this manual, keep it handy for future reference. January 2013 Hitachi America, Ltd.

  • Page 2

    Chapter 1 Table of Contents Table of Contents ........................2 Chapter 1 – General Description ..................3 Chapter 2 – Installation and Wiring ..................5 Chapter 3 – Configuring the Inverter ................... 9 Chapter 4 – Operation ......................11 Index ............................. 14 Document History January 2013 is the first edition.

  • Page 3: Chapter 1 – General Description

    The warranty period under normal installation and handling conditions shall be eighteen (18) months from the date of purchase, or twelve (12) months from the date of installation, whichever occurs first. The warranty shall cover repair or replacement, at Hitachi’s sole discretion, of the 115VIF-DIN interface board.

  • Page 4: Safety Precautions

    Chapter 1 SAFETY PRECAUTIONS HIGH VOLTAGE: This symbol indicates high voltage. It calls your attention to items or operations that could be dangerous to you and other persons operating this equipment. Read the message and follow the instructions carefully. WARNING: Indicates a potentially hazardous situation that, if not avoided, can result in serious injury or death.

  • Page 5: Chapter 2 – Installation And Wiring

    Chapter 2 Chapter 2 – Installation and Wiring Orientation to Product Features Figure 2-1 below shows the 115VIF-DIN interface. Figure 2-1, 115VIF-DIN Page 5 of 15...

  • Page 6

    Chapter 2 Installing the Interface Board WARNING: Remove power from the inverter and wait at least five minutes before moving to the next step. Open and remove the lower terminal cover. Confirm that the DC bus is fully discharged before proceeding further.

  • Page 7

    Chapter 2 Connecting the Board to the Inverter The method of connection of the 115VIF to the inverter depends on the inverter model. Refer to the appropriate section below for the inverter model you have. If using for traverse application, AC1 and AC2 are symmetrical in purpose.

  • Page 8

    Chapter 2 SJ700 When installed for use with an SJ700 inverter, the 115VIF-DIN must be mounted within the panel and in close proximity to the inverter. Please connect wiring leads (20 AWG) pigtail leads from the 115VIF-DIN to the I/O terminal strip of the SJ700 inverter.

  • Page 9: Chapter 3 – Configuring The Inverter, Chapter 4 – Operation, Index

    In order to achieve this basic functionality, the installation of the EzSQ C&H program must be downloaded to the inverter through the use of Hitachi ProDriveNext software. The software is available to download from our company website.

  • Page 10: Dip Switch

    Please remember to test the software with a disconnected load, and perform all activities and take all proper precautions before activating the software or inverter. Safety in operation should be the primary concern. Please visit our website at http://www.hitachi-america.us/ice/inverters/ for the ProDriveNext software and suggestive use crane and hoist program in our application notes section.

  • Page 11

    Program Flowchart and Index Two-Speed Operation The inverter can easily be configured for two-speed operation or infinitely variable speed operation by using the following parameter settings in lieu of or in addition to those in the table above: Parameter Function Setting Comment Code...

  • Page 12: Electrical Specifications

    Program Flowchart and Index Troubleshooting Symptom Remedy Inverter will not accelerate beyond minimum speed Input AC4 is not jumpered to HOT Inverter will only turn the motor in one direction Input AC5 is not jumpered to HOT Note: For other troubleshooting tips, refer to Chapter 6 of the pertinent inverter Instruction Manual Electrical Specifications The board does require power for the AC inputs, however, the outputs are powered from the inverter’s internal 24 Vdc power supply, drawing approximately 21 mA.

  • Page 13: Functionality Table

    Program Flowchart and Index Functionality Table (based on contact status) Up / Hi Speed Down / Hi Speed Up (AC1) Down (AC2) Side Limit (AC4) Up Limit (AC5) Motor Output (AC1 &AC3) (AC2 & AC3) Open Open Open Open Closed Closed No motor output Closed...

  • Page 14

    Program Flowchart and Index Index AC Input Wiring · 7 MIN speed · 11 Closed-loop · 8 Open-loop · 8 Configuration, inverter · 9 Operation · 11 Contents, carton · 3 Pendant · 7, 9 DIP switch · 10 Reset, fault · 10 Electrical Specifications ·...

  • Page 15

    Hitachi America, Ltd. Tarrytown, NY 10591 © 2009 http://www.hitachi-america.us/inverters January, 2013 HAL1055D...

This manual also for:

Sj700 series

Comments to this Manuals

Symbols: 0
Latest comments: