Table of Contents
Advertisement
7.1.5
Functions beginning with the key
The following functions are available to the user via the keypad:
1
sets the entire system (the same as key ABC)*
2
sets section A (the same as key A)*
3
sets A and B, or just B (the same as key B)*
4
event memory recall (key 4 scrolls backwards) – the control
panel records max. 255 of the latest events
5
new Master Code/Card (5 MC NC NC)
6
access code/card programming (6 MC nn NC)
7
for operation while under duress (should be entered before
the access code to secretly signal distress)
8
PGX control (ON/OFF = 81/80 or enter 8 to trigger if a
pulsed switching reaction is programmed)*
9
PGY control (ON/OFF = 91/90 or enter 9 to trigger if a
pulsed switching reaction is programmed)*
0
To enter Service Mode (0 SC – factory default 8080) or to
enter maintenance mode (0 MC – factory default 1234)
The functions allow the system to be operated from a mobile phone
keypad (if the control panel is equipped with the relevant communicator).
7.2
Programming access codes and cards
The system can be controlled by 4-digit codes and by access cards, of
the types PC-01 and PC-02 (EM UNIQUE 125kHz standard).
Sequences for programming access codes and cards are described in
the fig. 19. They should only be programmed in the DISARMED state.
The control panel has 1 service, 1 master and 50 user codes.
Only a numerical code can be used as a service code (factory
default 8080) – see the control panel programming section.
The master code can be a numerical code (factory default 1234) or an
access card. Using this master code/card, other users' codes and
cards can be programmed or erased. The master code/card is usually
used by the system administrator.
Each user from 01 to 50 can have a numerical code, or a card, or both
(factory default: all user codes and cards from 01 to 50 are erased).
If a user has both a code and a card, then it is possible to program
whether both a code and card must be presented to the system for
system access, or whether only one of them is required (see 6.37).
The system does not allow the same code or card to be
programmed to multiple positions. (if it is desired to move a
code/card to another position, the card/code has to be erased from its
current position first).
It is possible to display which code/card positions are already occupied
in maintenance mode (see 7.4.1).
The most convenient way to program codes and cards is by using a PC
running OLink software.
The control panel allows a maximum of 10 unsuccessful attempts in a
row to enter a valid code or card. If exceeded, a tamper alarm starts.
7.3
Setting and unsetting (arming/disarming) the
system
The system can be set and unset from a keypad, a keyfob or remotely by
phone or the Internet or from a PC running OLink software.
To set the system from a keypad:
Press key ABC, A or B,
Enter a code (or present a card)
If the system is partially set (section A is set), and you wish to extend
the proportion of the system which is set, press the B or ABC key. If
you extend the proportion of the system which is set, then all delayed
or next-delayed detectors in the section(s) going to be set and in the
section currently set, will provide an exit delay which means that if a
user has his system partially set (e.g. night setting) and wishes to exit
the house by walking through the sections that are still set, he will not
need to unset the whole system before leaving the house and setting
the whole system. The route used by the user to leave the house must
be covered by delayed or next-delayed detectors to make this possible
and must be considered at the system design stage.
To unset the system from a keypad:
Enter a valid access code (or present a card).
Operating the system from an outdoor keypad:
If the system is equipped with a JA-80H outdoor keypad or a JA-80N
external card reader then the outdoor device could either work the same way
as an indoor keypad unit or it could be programmed only to operate an
electric door lock (known as an outdoor-bypass feature), i.e. an indoor
keypad would then be used to control the alarm system. If the outdoor-
bypass feature is enabled then:
Setting and unsetting the alarm system is only possible using a JA-81F
or JA-81E indoor keypad or a keyfob.
Entering a valid access code or presenting a valid card to the outdoor
keypad or card reader will always open the electric door lock.
If the system is set, and the door is opened via the outdoor keypad or
reader, an entrance delay will begin. During this delay the system has
to be unset using an indoor keypad unit (or keyfob).
JA-83K control panel installation manual
7.4
Maintenance Mode
Maintenance mode can be entered using a master code or master card
by entering:
0 MC
where
MC = master code (card) – factory default 1234
In maintenance mode it is possible to:
Test devices (an alarm cannot be triggered).
Display which code/card positions are currently occupied.
Bypass individual devices (for one setting/unsetting cycle or
indefinitely) - see 7.4.2.
Program the real-time system clock – see 6.46.
Program the automatic setting/unsetting schedule – see 6.43.
Program telephone numbers for event reports to the end user (see
6.5).
Exit maintenance mode by pressing the # key.
7.4.1
Displaying which user/card positions are occupied
Which positions in the range 01 to 50 are occupied by codes or cards can
be displayed in maintenance mode as follows:
1. The control panel must be in maintenance mode – if not then enter 0
master code or card (factory default: 1234) while the system is totally
unset.
2. Press key 5 (the display indicates "Codes 01: Code"),
3. Using the arrow keys all user positions (01 to 50) can be scrolled
through, with the A indicator showing whether a code is
programmed or not, and the B indicator showing whether a card is
programmed or not.
4. To exit this code/card display mode press the # key.
5. To exit maintenance mode press the # key.
To change access codes and cards use sequence 6 MC nn NC (see fig.
19). (the system must be disarmed).
The most convenient way to administer codes is by using a PC running
OLink software (in the Codes window).
7.4.2
Bypassing devices
In maintenance mode it is possible to bypass (disable) individual system
devices (permanently or only for one setting/unsetting cycle):
1. The control panel must be in maintenance mode – if it is not, then enter
0 master code (factory default: 1234) while the system is totally unset.
2. Press key 1, to display the control panel's bypass menu.
1 and
3. Using the
able to trigger alarms.
4. To bypass a device use key:
2 to bypass the device for one setting/unsetting cycle (the
indicator will start flashing)
3 to permanently bypass a device (the
continuously)
5. To cancel the bypassing of a device use the same button as was
originally used for bypassing (2 or 3). Using key 4 will cancel all device
bypasses in the system.
6. All the desired bypasses can be programmed by repeating step 3 and 4.
7. Press the # key to exit the bypass menu. Pressing # again exits
maintenance mode.
If a system with bypasses programmed is being set, then bypass text will
be displayed on the keypad unit.
7.4.3
Protecting a car near the system
The OASiS system can also protect a car (cars) parked in the proximity
of the house.
1. If the car has a built-in car alarm then an RC-85 transmitter unit can be
connected to the car alarm output and the transmitter unit can be
enrolled to a free address in the OASiS control panel. (See the RC-85
manual) An alarm triggered in the car can be indicated as an OASiS
panic alarm (or a 24-hour reaction can be set), regardless of whether
the system is set or not. Note: if the car alarm confirms setting (arming)
by siren chirps appearing on the alarm output, then these should be
disabled to avoid false alarms.
2. If the car has no built-in car alarm then JA-85P or JA-85B
detectors can be installed in the car. The car detectors can be
assigned to their own dedicated section in the system, e.g. a split
system where section A could be for the car detectors, and section B
for the house detectors, with no detectors assigned to section C, and
the entry codes/cards assigned to section C to access the whole
system. So when the user enters the house he can set section A to
protect the car, and unset section B to be able to enter the house.
Radio communication supervision should be disabled for the car
detectors to avoid fault notifications when the car is driven away from
the house (see the detector manual).
- 14 -
7
keys you can scroll through all the devices
indicator will light
MKG51101
Advertisement
Table of Contents
