Table of Contents
Advertisement
ABC
hot key for setting the entire system (all sections
A, B & C)
A
hot key for setting section A (e.g. afternoon
partial setting of the garage)
B
in an unsplit system: hot key for setting
sections A and B (e.g. partial night-setting of the
garage and the ground floor).
in a split system: hot key for setting section B
(C is only set if both sections A and B are set)
?
Display
of
windows), fault details and PGX / PGY status.
turning on the PGX output from the keypad (the
same effect as ∗81)
turning off the PGX output from the keypad (the
same effect as ∗80)
Notes:
• The A and B keys only have a function if partial setting or
splitting are enabled.
• The keys
and
only control the PGX output if they have
been programmed for it, see 12.5.
13.1.5.
Functions beginning with the ∗ ∗ ∗ ∗ key
The following functions are available to the user via the
keypad:
∗ ∗ ∗ ∗ 1
sets the entire system (the same as key ABC)*
∗ ∗ ∗ ∗ 2
sets section A (the same as key A)*
∗ ∗ ∗ ∗ 3
sets A and B, or just B (the same as key B)*
∗ ∗ ∗ ∗ 4
event memory recall (key 4 scrolls backwards) – the
control panel records max. 255 of the latest events
∗ ∗ ∗ ∗ 5
new Master Code/Card (∗5 MC NC NC)
∗ ∗ ∗ ∗ 6
access code/card programming (∗6 MC nn NC)
∗ ∗ ∗ ∗ 7
for operation while under duress (should be entered
before the access code to secretly signal distress)
∗ ∗ ∗ ∗ 8
PGX control (ON/OFF = ∗81/∗80 or enter ∗8 to trigger if
a pulsed switching reaction is programmed)*
∗ ∗ ∗ ∗ 9
PGY control (ON/OFF = ∗91/∗90 or enter ∗9 to trigger if
a pulsed switching reaction is programmed)*
13.2.1.
Programming access codes and cards
Abbreviation
Name
SC
Service
MC
Master
UC
User
Installation manual: OASiS security system JA-82KRC-US
triggered
detectors
(e.g.
Number
Sequence
1
5 NC NC
1
∗ ∗ ∗ ∗ 5 MC NC NC
50
∗ ∗ ∗ ∗ 6 MC nn NC
∗ ∗ ∗ ∗ 0
To enter Service Mode (∗0 SC – factory default 8080)
or to enter maintenance mode (∗0 MC – factory default
1234)
The ∗ functions allow the system to be operated from a mobile phone
keypad (if the control panel is equipped with the relevant communicator).
13.2. Programming access codes and cards
The system can be controlled by 4-digit codes or by access
cards, of the types PC-01 and PC-02 (EM UNIQUE 125kHz
standard).
open
• The control panel has 1 service, 1 master and 50 user codes.
• Only a numerical code can be used as a service code (factory
default 8080) – see the control panel programming section.
• The master code can be a numerical code (factory default
1234) or an access card. Using this master code/card, other
users' codes and cards can be programmed or erased. The
master code/card is usually used by the system administrator.
• Each user from 01 to 50 can have a numerical code, or a
card, or both (factory default: all user codes and cards from
01 to 50 are erased).
• If a user has both a code and a card, then it is possible to
program whether both a code and card must be presented to
the system for system access, or whether only one of them is
required (see 12.37).
• The system does not allow the same code or card to be
programmed to multiple users. (if it is desired to move a
code/card to another user, the card/code has to be erased
from its current user first).
• It is possible to display which code/card positions are already
occupied in maintenance mode (see 13.4.1).
• The most convenient way to program codes and cards is by
using a PC running OLink software.
• The control panel allows a maximum of 10 unsuccessful
attempts in a row to enter a valid code or card. If exceeded, a
tamper alarm starts.
Notes
• Only programmable in Service Mode.
• NC = new code (must be entered twice) – a card cannot be used.
• Factory-default service code: 8080
• This code can be changed but not erased.
• Example: 5 4567 4567
• Only programmable if the system is totally unset (disarmed)
• MC = master code or card (factory default 1234)
• NC = new code or card entry – a numerical code has to be entered twice, but a
card only presented once
• Either a code or a card can be programmed as a master code (to have both is
impossible).
• The Master Code can be changed but not erased.
• The Master Code's reaction is set/unset and it is assigned to all sections.
• To reset the Master Code to the factory default 1234, enter 291 in Service Mode
(this will only affect the Master Code).
• To make handing over the system to the end user easier, we recommend
programming the system card (provided with the control panel) to the master
code.
• Example:
∗
5 1234 and then presenting the card to the keypad's RFID reader
• Only programmable if the system is totally unset
• MC = Master Code or card.
• nn = user code or card position from 01 to 50.
• NC = new code or card entry.
• Factory default: all user codes and cards are erased.
• Each user position can have both a card and a code programmed to it (by using
the sequence ∗6 MC nn NC twice)
• Each user code can have its own reaction programmed by an installer in Service
Mode, and with a split system, codes can be assigned to different sections.
• Example:
∗
6 1234 12 4345 (code 4345 will be programmed to user position 12)
To erase codes/cards enter:
∗ ∗ ∗ ∗ 6 MC nn 0000 erases the code and the card in user position nn.
∗ ∗ ∗ ∗ 6 MC 00 UC erases the code UC (or card UC) if programmed to any user position.
∗ ∗ ∗ ∗ 6 MC 00 0000 erases all user codes and cards in user positions 01 to 50.
19 / 21
MKH51400
Advertisement
Table of Contents
