Download Print this page

Creative Playthings 63081-102 Quick Start Manual

Ice cream stand

Advertisement

Quick Links

Ice Cream Stand
Usage:
The Ice Cream Stand is designed to fit on the end of the Lexington and
Williamsburg gyms, below the open end of the roof or tent. It will also fit
below the end of the clubhouse on the Yorktown and Ridgefield gyms
(see exceptions below). The Ice Cream Stand will also fit on the end of
the Skybox.
The Ice Cream Stand is not built to fit on the side, under the eaves, of
the Williamsburg gym.
No Rock Wall next to
Ice Cream Stand
No Chain Climber next to
Ice Cream Stand
Model:
63081-102
SPECIAL NOTES AND INSTRUCTIONS
The addition of the Ice Cream Stand to a
Creative Playthings gym will increase the
safe play zone requirements of the gym.
Please review the instructions and man-
ual provided with the gym for safety infor-
mation and instructions on proper ground
cover.
All hardware on this set is specially
coated for corrosion resistance. If non-
Creative Playthings hardware is used,
it must be galvanized or stainless steel.
IMPORTANT!
If the Ice Cream Stand is to be installed on a
Ridgefield or Yorktown gym DO NOT mount
a Rock Climber, Chain Climber, or Pinnacle
Rock Wall next to the Ice Cream Stand. There
is potential for head entrapment or other
conflict if any of these climbers are directly
adjacent to the Ice Cream Stand. There is
potential for serious injury or death!
No Pinnacle next to Ice
Cream Stand

Advertisement

loading
Need help?

Need help?

Do you have a question about the 63081-102 and is the answer not in the manual?

Questions and answers

Summary of Contents for Creative Playthings 63081-102

  • Page 1 63081-102 SPECIAL NOTES AND INSTRUCTIONS The addition of the Ice Cream Stand to a Creative Playthings gym will increase the safe play zone requirements of the gym. Please review the instructions and man- ual provided with the gym for safety infor- mation and instructions on proper ground cover.
  • Page 2 Lag Screw 5/16 x 3" Head Screw 1/4 x 1-1/2" Hex Bolt Lag Screw 5/16 x 4-1/2" 1/4 x 2" Lag Screw Page 2 Page 2 Ice Cream Stand Instructions - 19930-100L (08/20) Copyright 2016, Creative Playthings - Printed in U.S.A.
  • Page 3 Repeat the process, mounting the remaining Seat and Table Supports to the adjacent gym post. Ice Cream Stand Instructions - 19930-100L (08/20) Page 3 Page 3 Copyright 2016, Creative Playthings - Printed in U.S.A.
  • Page 4 Panel Assembly. The cleats on the bottom of the Panel fit between the Rafters. Secure the Panel to the Rafters using one#10 x 1-5/8" Screw in each hole. Page 4 Page 4 Ice Cream Stand Instructions - 19930-100L (08/20) Copyright 2016, Creative Playthings - Printed in U.S.A.
  • Page 5 Be sure not to drive the Screws too deep. The tips of the Screws must not poke through the top of the Table Boards. #10 x 1-5/8" Screw Ice Cream Stand Instructions - 19930-100L (08/20) Page 5 Page 5 Copyright 2016, Creative Playthings - Printed in U.S.A.
  • Page 6 Locate the 1" Hole Caps in the hardware bag. Install Hole Caps into all the counter-bored holes to cover the hardware. Page 6 Page 6 Ice Cream Stand Instructions - 19930-100L (08/20) Copyright 2016, Creative Playthings - Printed in U.S.A.