Table of Contents
Advertisement
Switching off the childproof lock
Press and hold the
button for approximately 4 seconds.
D
The
D
symbol in the display goes out. The childproof lock is
deactivated.
Changing the basic settings
Your oven has various basic settings. These settings can be
customised to suit your requirements.
Basic setting
c1 Clock display
c2 Signal duration upon
completion of a
cooking time or
timer period
c3 Waiting time until a
setting is applied
* Factory setting
No other time-setting option should have been set.
Cleaning system
The cleaning system regenerates the self-cleaning surfaces in
the cooking compartment.
The back wall, ceiling and side walls of the cooking
compartment are coated with a highly porous ceramic layer.
This coating absorbs and disintegrates splashes from baking
and roasting while the oven is in operation. If these self-
cleaning surfaces no longer clean themselves adequately, they
can be regenerated with the cleaning system.
Before cleaning
Remove accessories and cookware from the cooking
compartment.
Cleaning the cooking compartment floor
Before you set the cleaning system, clean the surfaces in the
cooking compartment that are not self-cleaning. Otherwise,
stains will develop that it is not possible to remove.
Use a dish cloth and hot soapy water or a vinegar solution. If
there are heavy deposits of dirt, use a stainless steel scouring
pad or oven cleaner. Only use when the cooking compartment
is cold. Never treat the self-cleaning surfaces with a scouring
pad or oven cleaner.
Setting
ó
Main oven
Set the function selector for the main oven to
1.
Set the temperature selector to
2.
Press the
button.
u
3.
Cleaning takes approximately one hour.
The
u
symbol lights up in the display. The time at which the
cleaning will end appears and the
Cleaning will start after a few seconds. You will see the time
counting down and the
r
goes out.
10
Selection 1 Selection 2 Selection 3
always*
only with
-
the
0
button
approx.
approx.
approx.
10 second
2 minutes*
5 minutes
s
approx.
approx.
approx.
2 seconds
5 seconds*
10 second
s
:
3D hot air.
.
s
p
symbol is in brackets.
symbol is in brackets. The
Press and hold the
1.
The current basic setting for the clock display is shown in the
display, e.g. c1 1 for selection 1.
Use the
@
2.
Confirm by pressing the
3.
The next basic setting appears in the display. You can scroll
through all levels with the
with the
@
To finish, press and hold the
4.
All basic settings are applied.
You may change the basic settings at any time.
Cleaning is finished
A signal sounds. The oven stops heating. 00:00 is shown in the
display. Press the
to the off position. The oven switches off.
Cancelling cleaning
Press the
u
position. The oven switches off.
Setting a later end time
You can postpone the time at which cleaning ends for the main
oven. This allows the cleaning programme to run at night,
for instance, so that you can use your oven during the day.
Make the settings as described in steps 1 to 3. Before cleaning
starts, use the
The main oven switches to standby. The display shows the time
at which the cleaning will finish and the
brackets. When cleaning starts, you can see the time counting
down in the display and the
symbol goes out.
ò
Top oven
Set the function selector for the top oven to
1.
heating.
Set the temperature selector to
2.
After approximately one hour, turn the function selector to the
3.
off position. The oven is switched off.
After cleaning
When the cooking compartment has cooled down completely,
wipe the salt residues off the self-cleaning surfaces with a
damp cloth.
p
symbol
0
button for approx. 4 seconds.
or
A
button to change the basic setting.
button.
0
0
button and change the setting
or
A
button.
button for approx. 4 seconds.
0
button twice and turn the function selector
0
button and turn the function selector to the off
or
button to set a later end time.
@
A
r
symbol is in brackets. The
s
p
symbol is in
p
Top/bottom
%
.
Advertisement
Table of Contents
