Subscribe to Our Youtube Channel
Related Manuals for Index TRAUB MS16
Summary of Contents for Index TRAUB MS16
- Page 1 Product note Base holder for boring slide INDEX MS16 Base holder 10156937 W9800029EN-02.02.18 1215/Rö - 20066621...
- Page 2 The duplication and distribution of this document or parts thereof is prohibited without prior consent of the copy- right owner, and any violators will be prosecuted. All rights, including the right to translate, are reserved. © Copyright by INDEX-Werke GmbH & Co. KG...
-
Page 3: Table Of Contents
TABLE OF CONTENTS Setup options on boring slide Z+ orientation ................................Z- orientation .................................. Base holder 10156937 Position X.2, delivery state ............................Position X.1, conversion ..............................Setup on boring slide Position X.2, Z+ orientation ............................Position X.1, Z- orientation ............................Conversion Z orientation, 30 ... - Page 4 Product note Base holder for boring slide W9800029EN-02.02.18...
-
Page 5: Setup Options On Boring Slide
Setup options on boring slide Z+ orientation • Base holder 10156937 can be mounted on the W-serration of the boring slide spindle away from the spindle Position X.2 Position X.1 Z- orientation • Base holder 10156937 can be mounted on the W-serration of the boring slide spindle near the spindle Position X.2 Position X.1... -
Page 6: Base Holder 10156937
Base holder 10156937 Position X.2, delivery state • Base holder with base body (1) and base plate (2) • Hydraulic expansion clamping sleeve (3) for adjustment in the Y-direction • Ball-ended thrust screws (4) for hydraulic expansion clamping sleeve • Mounting screws (5) on the boring sleeve •... -
Page 7: Position X.1, Conversion
Base holder 10156937 9 10 12 Position X.1, conversion • Delivery status (position X.2) dissemble into individual parts • or • remove base holder from boring slide X.2 and disassemble into individual parts 9 10 12 reassemble for position X.1: •... -
Page 8: Setup On Boring Slide
Setup on boring slide Position X.2, Z+ orientation • Position stop (8) (delivery state) on contact surface • Insert mounting screws (9) in the boring slide (13) • Turn in set screws (10) until stop (8) sits tight • Tighten mounting screws (9) •... -
Page 9: Position X.1, Z- Orientation
Setup on boring slide Position X.1, Z- orientation • Position stop (8) (delivery state) on contact surface • Insert mounting screws (9) in the boring slide (13) • Turn in set screws (10) until stop (8) sits tight • Tighten mounting screws (9) •... -
Page 10: Conversion Z Orientation, 30 Mm Offset
Setup on boring slide Conversion Z orientation, 30 mm offset 9 10 • Loosen mounting screws (5) on the boring slide (13) • Remove base holders (1+2) • Loosen and remove mounting screws (9) for stop (8) • Remove stop (8) •... -
Page 11: Inserting The Drill Holder
Inserting the drill holder • Insert the ball-ended thrust screws (4) to prevent the hydraulic expansion clamping sleeves (3) from falling out • Insert the drill holder (14) Product note Base holder for boring slide W9800029EN-02.02.18... -
Page 12: Axis Orientation
Axis orientation • Drill holder (14) should be already mounted • Insert mounting screws (5) in the boring slide (13) • Insert screws (7) to fix the angle adjustment • Attach dial gauge to drill holder (14) and measure • +/- 1° setting range possible •... -
Page 13: Y Orientation By Hydraulic Expansion Clamping Sleeve
• Do not clamp without a part • Use only original INDEX drill holders • Clamp only over the entire length of sleeve Temperature • Optimal temperature range between 10° and 50°... -
Page 14: Adjustment
Y orientation by hydraulic expansion clamping sleeve Adjustment • Attach dial gauge • Center drill holder (14) • Screw in hydraulic expansion clamping screw (15) until it stops • Check runout Product note Base holder for boring slide W9800029EN-02.02.18... -
Page 15: Adjusting Concentricity
Y orientation by hydraulic expansion clamping sleeve Adjusting concentricity • Loosen hydraulic expansion clamping screw (15) • Adjust the concentricity - by turning the hydraulic expansion clamping sleeve (3) using the ball-ended thrust screws (4) - by moving base holders (1+2) in X, see page 17 •... -
Page 16: Adjustment To Below 0.005 Mm
Y orientation by hydraulic expansion clamping sleeve Adjustment to below 0.005 mm • Check the adjustment after warm-up of the machine < 0,005mm Product note Base holder for boring slide W9800029EN-02.02.18... -
Page 17: Alignment In X- Spindle Center
Alignment in X- spindle center • Axis alignment and Y alignment should be done already • Insert mounting screws (5) • Loosen clamp (12) for adjusting screw (11) • Adjust spindle center in the X-direction with adjusting screw (11) • Measure drill holder with dial gauge •... - Page 18 Product note Base holder for boring slide W9800029EN-02.02.18...
- Page 19 Product note Base holder for boring slide W9800029EN-02.02.18...
- Page 20 INDEX-Werke GmbH & Co. KG Hahn & Tessky Plochinger Straße 92 D-73730 Esslingen Fon +49 711 3191-0 Fax +49 711 3191-587 info@index-werke.de www.index-werke.de...
Need help?
Do you have a question about the TRAUB MS16 and is the answer not in the manual?
Questions and answers