Table of Contents
Advertisement
Quick Links
1
APPLICATION ................................................................................. 3
2
DESCRIPTION (FIG. A-B-C) ........................................................... 3
3
PACKAGE CONTENT LIST ............................................................ 3
4
SYMBOLS ....................................................................................... 4
5
GENERAL SAFETY WARNINGS ................................................... 4
5.1
Working area .......................................................................................................... 4
5.2
Electrical safety ...................................................................................................... 4
5.3
Personal safety ...................................................................................................... 4
5.4
Power tool use and care ........................................................................................ 5
5.5
Service .................................................................................................................... 5
6
TABLE SAWS ................................................................................. 5
7
ELECTRICAL SAFETY ................................................................... 7
8
ADDITIONAL SAFETY INSTRUCTIONS FOR LASERS ............... 7
9
SPECIAL PRODUCT CHARACTERISTICS ................................... 8
10
INSTALLATION AND TRANSPORT .............................................. 8
10.1
Installation .............................................................................................................. 8
10.2
Transport ................................................................................................................ 8
10.2.1
Replacing the saw blade (Fig. 1) .............................................................................. 9
10.2.2
Mounting upper blade guard (Fig. 2) ........................................................................ 9
11
FUNCTIONS .................................................................................... 9
11.1
(Fig.3) ...................................................................................................................... 9
11.2
Converting the saw from mitre to table saw operating mode (Fig. 4) ................. 9
11.3
Adjustment of the turntable (Fig. 4-5) ................................................................. 10
11.4
Adjustment of the bevelling angle (Fig. 6) .......................................................... 10
11.5
Adjusting options table parallel fence (Fig. 7) ................................................... 10
11.6
Connection to a dust collector ............................................................................ 10
11.7
Assembly of dust bag (Fig.8) .............................................................................. 10
11.8
Laser line (Fig.9) .................................................................................................. 10
11.9
Work-light (Fig. 10)............................................................................................... 10
Copyright © 2021 VARO
POWX07583
P a g e
| 1
EN
www.varo.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Powerplus POWX07583
Summary of Contents for Powerplus POWX07583
-
Page 1: Table Of Contents
POWX07583 APPLICATION ................. 3 DESCRIPTION (FIG. A-B-C) ............3 PACKAGE CONTENT LIST ............3 SYMBOLS ..................4 GENERAL SAFETY WARNINGS ........... 4 Working area ......................4 Electrical safety ...................... 4 Personal safety ...................... 4 Power tool use and care ..................5 Service ........................ - Page 2 POWX07583 11.10 Install vertical clamping device (Fig. 11) ............11 11.11 Mounting the side extensions (Fig. 12)............... 11 11.11.1 Connection to AC power ..................11 OPERATIONS ................11 12.1 Cross-cut sawing mode ..................12 12.1.1 Settings ........................12 12.1.2 Mitre 90° and turntable 90° (Fig. 13) ..............12 12.1.3...
-
Page 3: Application
POWX07583 MITRE SAW WITH TOP TABLE POWX07583 1 APPLICATION The machine is designed for sawing wood, metal and plastic. It is not designed for commercial use. WARNING! Read this manual and general safety instructions carefully before using the appliance, for your own safety. Your power tool should only be passed on together with these instructions. -
Page 4: Symbols
POWX07583 If any parts are missing or damaged, please contact your dealer 4 SYMBOLS In this manual and/or on the machine the following symbols are used: In accordance with essential Denotes risk of personal requirements of the European injury or damage to the tool. -
Page 5: Power Tool Use And Care
POWX07583 Use safety equipment. Always wear eye protection. Using safety equipment such as a dust mask, non-skid safety shoes, a hard hat, or hearing protection whenever it is needed will reduce the risk of personal injury. Avoid accidental starts. Ensure the switch is in the off position before inserting the plug. - Page 6 POWX07583 Before each use, check the saw blade for small cracks or damages. Replace a cracked or damaged blade immediately. Never use saw blades made of high-speed steel (HSS). Only use saw blades that are recommended by the manufacturer and that fulfil the EN847- 1 standard.
-
Page 7: Electrical Safety
POWX07583 not sawing any twisted or skewed wood pieces, or pieces that do not have a straight edge for moving along the rip fence, in a longitudinal direction. Do not carry out any free-hand operations. Free-hand means that you use your hands for supporting the workpiece, or for leading it with your hands, instead of using the rip fence or the mitre block. -
Page 8: Special Product Characteristics
POWX07583 9 SPECIAL PRODUCT CHARACTERISTICS Quick change-over between cross-cut and table saw mode. 45° sawing range for beveling. (45° left) 90° sawing range for bevelling (45° left or 45° right) with five preset stops Perfectly suited for mobile use, due to its low weight and small dimensions ... -
Page 9: Replacing The Saw Blade (Fig. 1)
POWX07583 10.2.1 Replacing the saw blade (Fig. 1) Set the saw to crosscut and mitre saw mode. Place the blade spanner on the outer flange and undo the saw blade screw (a) by turning it in a clockwise direction using the Hex key S6. Remove the saw blade screw (a) and the outer flange. -
Page 10: Adjustment Of The Turntable (Fig. 4-5)
POWX07583 11.3 Adjustment of the turntable (Fig. 4-5) Turn the turntable locking knob (9) approx. 2 turns counter-clockwise, then adjust the turntable (11) by pressing the angle adjustment control button (23). The turntable (11) has locking points at angles of 0°, 15°, 22.5°, 31.6° and 45°. Once the turntable (11) is engaged, the setting must also be secured by turning the turntable locking knob (9) clockwise. -
Page 11: Install Vertical Clamping Device (Fig. 11)
POWX07583 11.10 Install vertical clamping device (Fig. 11) Find out the vertical clamping device set (25). Insert the iron bar of the vertical clamping device set into the back hole of the reference ruler (13). Adjustable Wing Screws to select height as required. Control the adjustable height of the wing screw. -
Page 12: Cross-Cut Sawing Mode
POWX07583 12.1 Cross-cut sawing mode 12.1.1 Settings When the bevel lock (16) is loosened, you can tilt the machine head to the left by up to 45°. The turntable (11) can be adjusted from -45° to +45° by undoing the turntable locking knob (9). -
Page 13: On/Off Switch (Fig. 17)
POWX07583 Undo the bevel lock (16) and use the cutting handle (6) to tilt the machine head to the left until it coincides with the required angle value. Screw the bevel lock (16) back down again. 12.2 Table saw mode 12.2.1... -
Page 14: Maintenance
POWX07583 13.2 Maintenance Our machines have been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper machine care and regular cleaning. 13.3 Cleaning Use a brush, a dust cloth or vacuum cleaner, to remove all wood chips and sawdust from: ... -
Page 15: Warranty
We also disclaim all liability for any bodily injury resulting from inappropriate use of the tool. Repairs may only be carried out by an authorised customer service centre for Powerplus tools. You can always obtain more information at the number 00 32 3 292 92 90. -
Page 16: Declaration Of Conformity
POWX07583 18 DECLARATION OF CONFORMITY VARO N.V. - Vic. Van Rompuy N.V. Joseph Van Instraat 9 - BE2500 Lier - BELGIUM, declares that, Product: Mitre saw with top table Trade mark: PowerPlus Model: POWX07583 is in conformity with the essential requirements and other relevant provisions of the applicable European Directives, based on the application of European harmonized standards.
Need help?
Do you have a question about the POWX07583 and is the answer not in the manual?
Questions and answers