Mantis Compact - Vision Engineering Mantis Compact User Manual

MANTIS COMPACT

Packing Contents
MANTIS COMPACT
Universal mount
Packing Contents
G-clamp
Universal mount
Counter balanced boom stand
G-clamp
Viewing head
Counter balanced boom stand
Power adapter
Viewing head
Objective lens
Power adapter
Assembly
Objective lens
1
Secure the universal mount to the work
Assembly
surface using the G-clamp provided or by
using appropriate screws located in the
1
Secure the universal mount to the work
holes of the mount.
surface using the G-clamp provided or by
2
Place the universal arm on top of the
using appropriate screws located in the
universal mount and lower it on to the
holes of the mount.
spigot until it is fully mounted.
2
Place the universal arm on top of the
3
Loosen the upper retaining bolt
universal mount and lower it on to the
universal arm. Remove the lower retaining
spigot until it is fully mounted.
�
bolt . Carefully place the locating hook
3
Loosen the upper retaining bolt
of the Mantis viewing head
universal arm. Remove the lower retaining
upper retaining bolt of the universal arm.
�
bolt . Carefully place the locating hook
Replace the lower retaining bolt
of the Mantis viewing head
that the bolt passes through the lower locating mount
upper retaining bolt of the universal arm.
of the Mantis viewing head.
Replace the lower retaining bolt
Tighten the upper and lower retaining bolts then re-seat the universal arm rubber
that the bolt passes through the lower locating mount
�
gaiter
of the Mantis viewing head.
4
Remove the red transit plug from the underneath of the viewing head.
Tighten the upper and lower retaining bolts then re-seat the universal arm rubber
�
gaiter .
5
Fit and lock the chosen objective lens into the objective seat.
4
Remove the red transit plug from the underneath of the viewing head.
6
Ensuring the power adapter is suitable for your supply voltage, connect the power adapter
5
plug to a suitable power outlet and its output connector to the base of the universal arm.
Fit and lock the chosen objective lens into the objective seat.
7
Connect the output lead at the top of the universal arm to the rear of the viewing head.
6
Ensuring the power adapter is suitable for your supply voltage, connect the power adapter
Do not attempt to connect the power adapter directly to the viewing head.
plug to a suitable power outlet and its output connector to the base of the universal arm.
7
Connect the output lead at the top of the universal arm to the rear of the viewing head.
Routine Maintenance
Do not attempt to connect the power adapter directly to the viewing head.
Desiccant Replacement
Routine Maintenance
The desiccant removes excess moisture from the optical
head.
Desiccant Replacement
Disconnect the power supply from the bottom of the
The desiccant removes excess moisture from the optical
head.
head.
Remove the screw securing the desiccant cover
Disconnect the power supply from the bottom of the
the cover off.
head.
Insert the new desiccant and replace the desiccant cover.
Remove the screw securing the desiccant cover
LED Arrays
the cover off.
Insert the new desiccant and replace the desiccant cover.
Remove the desiccant cover
LED Arrays
Remove the two crosshead screws that secure the LED
�
array
Remove the desiccant cover
Reassembly is the reverse of this procedure.
Remove the two crosshead screws that secure the LED
�
array and remove the array complete with filters
Reassembly is the reverse of this procedure.
6
Mantis Compact with Universal Stand - User Guide
6
Mantis Compact with Universal Stand - User Guide
(sold seperately)
�
in the
�
in the
�
over the
�
, ensuring
�
over the
�
, ensuring
.
�
.
and remove the array complete with filters
�
.
�
and lift
�
and lift
�
.
�
.
4
www.visioneng.com/support
www.visioneng.com/support