Table of Contents
Advertisement
Font Size
Not used.
Short Format
Use to set the method for omitting characters when the name
of a button is truncated.
From First: Truncate trailing characters that cannot be
displayed, displaying the start of the character string.
First+Last: Truncate mid characters, displaying the start and
end of the character string.
New Line
(Not available on the MKS-R3210)
Sets the position of a line break in the connector name
displayed on operation buttons.
Disable: Line break is not used.
Enable: Add line break at the position where a "|" (vertical
bar) character is entered.
Brightness Level
Set the brightness of the operation buttons and display
windows using 5 gradations: 1 (dark) to 5 (bright). Select the
brightness according to the operating environment.
Brightness Level (Status Display)
(Enabled only on MKS-R1630)
Set the brightness of the status display windows using 5
gradations: 1 (dark) to 5 (bright). Select the brightness
according to the operating environment.
Destination Key Display Mode
(Not available on the MKS-R3210)
Changes the display of operation buttons for which only a
destination is configured.
Destination Name: Display the destination name, regardless
of the source/destination selection mode state.
XPT Source Name: Display the crosspoint status (source
name) in source selection mode, and displays the
destination name in destination selection mode.
• "..." is displayed when a crosspoint is not connected.
• Displays the topmost level in level breakaway state.
• Displays the source with the lowest number if multiple
sources exist.
Both(2-Line Display): In source selection mode, display the
source name/destination name on two lines. In
destination selection mode, display the destination name.
The source/destination display position is determined by
the [Dest Position (Status & Dest Key)] setting. The
inverted display position is determined by the [Invert
Display Position] setting.
Invert Display Position (Dest Key)
(Not available on the MKS-R3210)
When [Both(2-Line Display)] is selected in [Destination Key
Display Mode] to display the source name and destination
name on two lines in the MKS-R1620 display window or
MKS-R1630 selection button, this sets which line is displayed
inverted.
Top: Invert the top line.
Bottom: Invert the bottom line.
Dest Position (Status & Dest Key)
(Not available on the MKS-R3210)
When [Both(2-Line Display)] is selected in [Destination Key
Display Mode] to display the source name and destination
name on two lines in the MKS-R1620 display window or
MKS-R1630 selection button, this sets which line displays the
destination.
Also, when displaying the source name and destination name
on two lines in the MKS-R1630 status display window, this
sets which line displays the destination.
Top: Display the destination on the top line.
Bottom: Display the destination on the bottom line.
Breakaway
Breakaway Display Mode
Top Level: Display the crosspoints of the top level only.
All Level: Display the crosspoints of all levels.
Breakaway Color
Set the color of buttons when a different source is selected for
each level (or color displayed in button block on the MKS-
1620).
Same as Color Settings: Display the color configured using
[Color Settings] in [Display Settings].
1: Displays white.
2: Displays amber.
3: Displays yellow.
4: Displays green.
5: Displays purple.
6: Displays light blue.
7: Displays dark blue.
8: Displays pink.
Alias Priority
Main LCD
Display Priority #1 to #5
(Enabled only on MKS-R1630)
Set whether the base name or alias name has priority for display
as the connector name in the status display window.
The status display window has several display modes, and up to
five connector names can be displayed in each display mode.
BASE: Display the base name.
1 to 8: Display the Alias1 to Alias8 name.
Sub LCD
Display Priority
Select the base name or alias name for the connector names
to display in the display window and preset display window.
BASE: Display the base name.
1 to 8: Display the Alias1 to Alias8 name.
2-Line Display
Display Priority
(Not available on the MKS-R3210)
Select the base name or alias name for the connector names
to display on the selection button for 2-line display.
BASE: Display the base name.
1 to 8: Display the Alias1 to Alias8 name.
Retrace Settings Page
Use to configure the function for tracing the crosspoint status
display and to display the source names of sources.
1
Enter data in the [Retrace Settings] table.
30
Hide quick links:
Advertisement
Table of Contents
