Gallagher T11 Mifare Reader Black Installation Note
Hide thumbs
Also See for T11 Mifare Reader Black:
- Installation note (11 pages) ,
- Installation note (11 pages)
Advertisement
Gallagher
T11 Reader
Installation Note
T11 Mifare Reader Black: C300410
T11 Mifare Reader White: C300411
T11 Multi Tech Reader Black: C300430
T11 Multi Tech Reader White: C300431
3E4289 Gallagher T11 Reader | Edition 1 | August 2016
Copyright © Gallagher Group Limited
T11 PIV Reader Black: C305410
T11 PIV Reader White: C305411
T11 PIV Reader - Multi Tech Black: C305430
T11 PIV Reader - Multi Tech White: C305431
Page 1
Advertisement
Table of Contents
Related Manuals for Gallagher T11 Mifare Reader Black
Summary of Contents for Gallagher T11 Mifare Reader Black
- Page 1 T11 PIV Reader - Multi Tech Black: C305430 T11 Multi Tech Reader Black: C300430 T11 Multi Tech Reader White: C300431 T11 PIV Reader - Multi Tech White: C305431 3E4289 Gallagher T11 Reader | Edition 1 | August 2016 Copyright © Gallagher Group Limited Page 1...
- Page 2 Although every commercially reasonable effort has been taken to ensure the quality and accuracy of the information, Gallagher Group makes no representation as to its accuracy or completeness and it should not be relied on as such. To the extent permitted by law, all express or implied, or other representations or warranties in relation to the information are expressly excluded.
-
Page 3: Table Of Contents
Installation ............................8 LED indications ..........................10 Accessories ............................ 10 Technical specifications ........................11 Approvals and standards ........................ 12 Mounting dimensions ........................13 3E4289 Gallagher T11 Reader | Edition 1 | August 2016 Copyright © Gallagher Group Limited Page 3... -
Page 4: Introduction
Introduction The Gallagher T11 Reader is a mobile credential and smart card proximity reader. It can be installed as either an entry reader or exit reader. It can be mounted on a vertical, rectangular 50 mm x 75 mm (2" x 3") flush box with mounting holes spaced at a nominal 85 mm (3.25"). -
Page 5: Before You Begin
4 x 40 mm No.6 self tapping, pan head, Phillips drive fixing screws 2.2 Power supply The Gallagher T11 Reader is designed to operate over a supply voltage range of 9 - 16 Vdc measured at the reader terminals. The operating current draw is dependant on the supply voltage at the reader. - Page 6 Device HBUS devices Controller 6000 HBUS HBUS HBUS HBUS Device Device Device Device HBUS Module Terminate Terminate HBUS HBUS Device Device Terminate Terminate 3E4289 Gallagher T11 Reader | Edition 1 | August 2016 Copyright © Gallagher Group Limited Page 6...
-
Page 7: Distance Between Readers
(21 AWG) * The matching of wire sizes to equivalent wire gauges are only approximate. ** Recommended cable types for optimal HBUS RS485 performance. *** Not applicable for PIV or Gallagher mobile credential reader installations. Notes: • Shielded cable may reduce the obtainable cable length. Shielded cable should be grounded at the Controller end only. -
Page 8: Installation
Ensure both you and the equipment are earthed before beginning any servicing. The Gallagher T11 Reader is designed to be mounted on vertically orientated electrical flush (gang) boxes, or any solid flat surface. However installation on metal surfaces, particularly those with a large surface area will reduce read range. - Page 9 Gallagher PIV readers connect to the Gallagher Controller 6000 High Spec PIV (C305101) only. An HBUS Reader connects to a Gallagher Controller 6000, Gallagher 4H/8H Module (attached to a Controller 6000) or a Gallagher HBUS Door Module (connected to a Controller 6000).
-
Page 10: Led Indications
Flashes Green Access has been granted. Flashes Red Access has been denied. Flashes (Blue) Reading and validating a PIV card. Reading a Gallagher mobile credential. LED (squiggle) Cardax IV indication 3 Flash (Amber) No communications with the Controller. On (Green or Red) Fully configured and functioning normally. -
Page 11: Technical Specifications
The reader is idle. Peak current during card read. Gallagher T Series readers are UL humidity tested and certified to 85% and have been independently verified to 95%. Note: The current values stated above have been reported using the default configuration for a reader in Command Centre. -
Page 12: Approvals And Standards
US - Equipment: com, burg and acc reader CA - Equipment: com, burg reader Please refer to the document “3E2793 Gallagher Command Centre UL Configuration Requirements” for a guide to configuring the Gallagher system to the appropriate UL Standard. 3E4289 Gallagher T11 Reader | Edition 1 | August 2016 Copyright ©... -
Page 13: Mounting Dimensions
(0.89") 125 Card read area 40 mm (1.57") 70 mm (2.76") IMPORTANT This picture is not to scale, therefore use the measurements provided. 3E4289 Gallagher T11 Reader | Edition 1 | August 2016 Copyright © Gallagher Group Limited Page 13...