Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Gallagher T10
Summary of Contents for Gallagher T10
- Page 1 Installation Note T10 MIFARE® Reader, Black: C300400 T10 MIFARE® Reader, White: C300401 High Sec T10 Reader, Black: C305400 High Sec T10 Reader, White: C305401 3E4288 Gallagher T10 Reader | Edition 11 | March 2023 Copyright © Gallagher Group Limited Page 1...
- Page 2 Although every commercially reasonable effort has been taken to ensure the quality and accuracy of the information, Gallagher Group makes no representation as to its accuracy or completeness and it should not be relied on as such. To the extent permitted by law, all express or implied, or other representations or warranties in relation to the information are expressly excluded.
-
Page 3: Table Of Contents
Installation ............................7 LED indications ..........................9 Accessories ............................9 Technical specifications ........................10 Approvals and Compliance Standards.................... 10 Mounting Dimensions ........................12 3E4288 Gallagher T10 Reader | Edition 11 | March 2023 Copyright © Gallagher Group Limited Page 3... -
Page 4: Introduction
Introduction The Gallagher T10 Reader is a smart card proximity reader. It can be installed as either an entry reader or exit reader. The reader sends information to the Gallagher Controller and acts upon information sent from the Gallagher Controller. The reader itself does not make any access decisions. - Page 5 The end devices on the HBUS cable should be terminated using 120 ohms resistance. To terminate the Gallagher Controller 6000, connect the supplied on-board termination jumpers to the Controller. To terminate a reader, connect the orange (termination) wire to the green (HBUS A) wire.
-
Page 6: Distance Between Readers
When mounting a proximity reader on an internal wall, check that any reader fixed to the other side of the wall is not less than 200 mm (8 in) away. 200 mm 3E4288 Gallagher T10 Reader | Edition 11 | March 2023 Copyright © Gallagher Group Limited Page 6... -
Page 7: Installation
Ensure both you and the equipment are earthed before beginning any servicing. The Gallagher T10 Reader is designed to be mounted on any solid flat surface. However installation on metal surfaces, particularly those with a large surface area will reduce read range. The extent to which the range is reduced will depend upon the type of metal surface. - Page 8 Insert the M3 Torx Post Security screw (using a T10 Torx Post Security screwdriver) through the hole at the bottom of the bezel to secure the facia assembly.
-
Page 9: Led Indications
Flashes Green Access has been granted. Flashes Red Access has been denied. Flashes (Blue) Reading and validating a PIV card. Reading a Gallagher mobile credential. LED (squiggle) Cardax IV indication 3 Flash (Amber) No communications with the Controller. On (Green or Red) Fully configured and functioning normally. -
Page 10: Technical Specifications
The reader is idle. Maximum reader current during card read. Gallagher T Series readers are UL humidity tested and certified to 85% and have been independently verified to 95%. Reader currents verified by UL are provided in the document "3E2793 Gallagher Command Centre UL Configuration Requirements". - Page 11 UL compliant. AS/NZS IEC 60839.11.1:2019 Grade 4, Class II C300400 only The C300400 variant of the T10 Readers is the only variant that complies with BIS. HVIN FCC ID IC ID...
-
Page 12: Mounting Dimensions
13 mm (1/2") diameter hole for cable 22.5 mm (0.89") 35 mm (1.38") IMPORTANT This picture is not to scale, therefore use the measurements provided. 3E4288 Gallagher T10 Reader | Edition 11 | March 2023 Copyright © Gallagher Group Limited Page 12...