Subscribe to Our Youtube Channel
Related Manuals for WAGO 750-557/040-000
Summary of Contents for WAGO 750-557/040-000
- Page 1 Manual WAGO-I/O-SYSTEM 750 XTR 750-557/040-000 4AO +/-10V DC /XTR 4-Channel Analog Output Module, ±10 VDC /XTR Version 1.3.0...
- Page 2 We wish to point out that the software and hardware terms as well as the trademarks of companies used and/or mentioned in the present manual are generally protected by trademark or patent. WAGO is a registered trademark of WAGO Verwaltungsgesellschaft mbH. Manual Version 1.3.0...
-
Page 3: Table Of Contents
WAGO-I/O-SYSTEM 750 XTR Table of Contents 750-557/040-000 4AO +/-10V DC /XTR Table of Contents Notes about this Documentation ............. 5 Validity of this Documentation..............5 Copyright ....................5 Symbols ....................6 Number Notation ..................8 Font Conventions ................... 8 Important Notes ..................9 Legal Bases .................... - Page 4 Table of Contents WAGO-I/O-SYSTEM 750 XTR 750-557/040-000 4AO +/-10V DC /XTR Connection Example ................38 Use in Hazardous Environments ............39 Marking Configuration Examples ............40 7.1.1 Marking for Europe According to ATEX and IECEx ......40 7.1.2 Marking for the United States of America (NEC) and Canada (CEC) ................
-
Page 5: Notes About This Documentation
(4AO +/-10V DC /XTR). The I/O module 750-557/040-000 shall only be installed and operated according to the instructions in this manual, in the system description for the WAGO-I/O- SYSTEM 750 XTR and in the manual for the used fieldbus coupler/controller. -
Page 6: Symbols
Notes about this Documentation WAGO-I/O-SYSTEM 750 XTR 750-557/040-000 4AO +/-10V DC /XTR Symbols Personal Injury! Indicates a high-risk, imminently hazardous situation which, if not avoided, will result in death or serious injury. Personal Injury Caused by Electric Current! Indicates a high-risk, imminently hazardous situation which, if not avoided, will result in death or serious injury. - Page 7 WAGO-I/O-SYSTEM 750 XTR Notes about this Documentation 750-557/040-000 4AO +/-10V DC /XTR Additional Information: Refers to additional information which is not an integral part of this documentation (e.g., the Internet). Manual Version 1.3.0...
-
Page 8: Number Notation
Notes about this Documentation WAGO-I/O-SYSTEM 750 XTR 750-557/040-000 4AO +/-10V DC /XTR Number Notation Table 1: Number Notation Number Code Example Note Decimal Normal notation Hexadecimal 0x64 C notation Binary '100' In quotation marks, nibble separated '0110.0100' with dots (.) -
Page 9: Important Notes
2.1.1 Subject to Changes WAGO Kontakttechnik GmbH & Co. KG reserves the right to provide for any alterations or modifications. WAGO Kontakttechnik GmbH & Co. KG owns all rights arising from the granting of patents or from the legal protection of utility patents. -
Page 10: Technical Condition Of Specified Devices
These modules contain no parts that can be serviced or repaired by the user. The following actions will result in the exclusion of liability on the part of WAGO Kontakttechnik GmbH & Co. KG: •... -
Page 11: 2.1.4.1.2 Packaging
WAGO-I/O-SYSTEM 750 XTR Important Notes 750-557/040-000 4AO +/-10V DC /XTR • Observe national and local regulations for the disposal of electrical and electronic equipment. • Clear any data stored on the electrical and electronic equipment. • Remove any added battery or memory card in the electrical and electronic equipment. -
Page 12: Safety Advice (Precautions)
Always adhere to the EMC directives applicable to your application. Power from SELV/PELV power supply only! All field signals and field supplies connected to this XTR I/O module (750-557/040-000) must be powered from SELV/PELV power supply(s)! Manual Version 1.3.0... - Page 13 WAGO-I/O-SYSTEM 750 XTR Important Notes 750-557/040-000 4AO +/-10V DC /XTR Do not touch hot surfaces! The surface of the housing can become hot during operation. If the device was operated at high ambient temperatures, allow it to cool off before touching it.
- Page 14 Important Notes WAGO-I/O-SYSTEM 750 XTR 750-557/040-000 4AO +/-10V DC /XTR Avoid electrostatic discharge! The devices are equipped with electronic components that may be destroyed by electrostatic discharge when touched. Please observe the safety precautions against electrostatic discharge per DIN EN 61340-5-1/-3. When handling the devices, please ensure that environmental factors (personnel, work space and packaging) are properly grounded.
-
Page 15: Device Description
The meaning of the LEDs is described in the “Display Elements” section. Power to the internal electronics is supplied via internal data bus. The I/O module 750-557/040-000 (4AO +/-10V DC /XTR) receives the 24 V voltage supply for the field level from an upstream I/O module or from the fieldbus coupler/controller via blade-formed power jumper contacts. - Page 16 Device Description WAGO-I/O-SYSTEM 750 XTR 750-557/040-000 4AO +/-10V DC /XTR Increased interference! For standard-compliant application in substation instrumentation and control, telecontrol systems, railway technology or shipbuilding certified operation, field-side power supply filter 750-624/040-001 or power supply filter 750-626/040-000 are generally to be used for XTR module groups.
-
Page 17: View
WAGO-I/O-SYSTEM 750 XTR Device Description 750-557/040-000 4AO +/-10V DC /XTR View Figure 1: View Table 3: Legend for Figure “View” Pos. Description Details See Section Marking possibility with Mini- “Device Description” > “Display Elements” Status LEDs “Device Description” > “Connectors”... -
Page 18: Connectors
Device Description WAGO-I/O-SYSTEM 750 XTR 750-557/040-000 4AO +/-10V DC /XTR Connectors 3.2.1 Data Contacts/Local Bus Communication between the fieldbus coupler/controller and the I/O modules as well as the system supply of the I/O modules is carried out via the local bus. The contacting for the local bus consists of 6 data contacts, which are available as self-cleaning gold spring contacts. -
Page 19: Power Jumper Contacts/Field Supply
The blade contacts are sharp-edged. Handle the I/O module carefully to prevent injury. Do not touch the blade contacts. The I/O module 750-557/040-000 has 2 self-cleaning power jumper contacts that supply and transmit power for the field side. The contacts on the left side of the I/O module are designed as blade contacts and those on the right side as spring contacts. -
Page 20: Cage Clamp ® Connectors
I/O module can be achieved even in the presence of interference acting on the signal cable. For further information about shielding, see system manual WAGO-I/O-SYSTEM 750 XTR, section “Connect Devices” > … > “Shielding.”... -
Page 21: Display Elements
Function Operational readiness and trouble-free local bus Green communication No error Error Overload or short circuit to ground in one of the output channels Operating Elements The I/O module 750-557/040-000 has no operating elements. Manual Version 1.3.0... -
Page 22: Schematic Diagram
Device Description WAGO-I/O-SYSTEM 750 XTR 750-557/040-000 4AO +/-10V DC /XTR Schematic Diagram Figure 6: Schematic Diagram Manual Version 1.3.0... -
Page 23: Technical Data
WAGO-I/O-SYSTEM 750 XTR Device Description 750-557/040-000 4AO +/-10V DC /XTR Technical Data 3.6.1 Device Data Table 7: Technical Data – Device Width 12 mm Height (from upper edge of DIN-rail) 60.6 mm Depth 100 mm Weight 53.5 g Degree of protection IP20 3.6.2... -
Page 24: Outputs
Device Description WAGO-I/O-SYSTEM 750 XTR 750-557/040-000 4AO +/-10V DC /XTR 3.6.4 Outputs Table 10: Technical Data – Outputs No. of outputs > 5 kΩ Load impedance Signal voltage ±10 V Resolution 12 bit Conversion time 10 ms typ. Recovery time 100 ms typ. -
Page 25: Climatic Environmental Conditions
WAGO-I/O-SYSTEM 750 XTR Device Description 750-557/040-000 4AO +/-10V DC /XTR 3.6.7 Climatic Environmental Conditions Table 15: Technical Data ‒ Climatic Environmental Conditions −40 °C … +70 °C Surrounding air temperature, operation −40 °C … +85 °C Surrounding air temperature, storage... -
Page 26: Approvals
The following approvals have been granted to 750-557/040-000 I/O modules: Conformity Marking UL508 Korea Certification MSIP-REM-W43-AOM750 The following Ex approvals have been granted to 750-557/040-000 I/O modules: ANSI/ISA 12.12.01 Class I, Div2 ABCD T4 TÜV 17 ATEX 193969 X II 3 G Ex ec IIC T4 Gc IECEx TUN 16.0046X... -
Page 27: Standards And Guidelines
WAGO-I/O-SYSTEM 750 XTR Device Description 750-557/040-000 4AO +/-10V DC /XTR Standards and Guidelines 750-557/040-000 I/O modules meet the following standards and guidelines: Table 16: Standards and Rated Conditions for Explosion Protection Applications ATEX acc. Directive 2014/34/EU General Requirements EN 60079-0:2012 + A11:2013... -
Page 28: Table 17: Climatic And Mechanical Environmental Conditions And Shipbuilding
Device Description WAGO-I/O-SYSTEM 750 XTR 750-557/040-000 4AO +/-10V DC /XTR Table 17: Climatic and Mechanical Environmental Conditions and Shipbuilding Standard Test Value Transport EN 60870-2-2 Ct2(2k4) (except precipitation/water/moisture) Mechanical Environmental Conditions EN 61850-3 Achieved EN 60870-2-2 EN 60721-3-1 EN 60721-3-3... -
Page 29: Table 18: Emc - Immunity To Interference
WAGO-I/O-SYSTEM 750 XTR Device Description 750-557/040-000 4AO +/-10V DC /XTR The I/O module 750-557/040-000 meets the following EMC standards as these standards relate to the I/O module: Table 18: EMC – Immunity to Interference Standard Test Value Electrostatic Discharge • EN 61000-4-2 8 kV (contact discharge) •... - Page 30 Device Description WAGO-I/O-SYSTEM 750 XTR 750-557/040-000 4AO +/-10V DC /XTR Table 18: EMC – Immunity to Interference Standard Test Value Line Frequency Disturbances • EN 60255-26 Standard not applicable Alternating Components of the Voltage to DC Line Connections • EN 61000-4-17 15 % •...
-
Page 31: Table 19: Emc - Emission Of Interference
WAGO-I/O-SYSTEM 750 XTR Device Description 750-557/040-000 4AO +/-10V DC /XTR Table 19: EMC – Emission of Interference Standard Test Value Enclosure Emission of Interference • EN 61000-6-3 30 dB(µV/m), QP, 30 MHz … 230 MHz • EN 55022 Class B 37 dB(µV/m), QP, 230 MHz …... -
Page 32: Table 20: Standards And Rated Conditions For Rail Applications (En 50155)
EN 50121-3-2 5.5 EMC (Emission of Interference, EN 50121-3-2 Immunity to Interference) EN 50121-4 EN 50121-5 9.11 Materials (Fire Protection) EN 45545-2 Hazard level HL3 WAGO is a company certified in accordance with the IRIS quality standard. Manual Version 1.3.0... -
Page 33: Process Image
“I/O Modules” included in the description concerning the process image of the corresponding coupler/controller. For the I/O module 750-557/040-000, the numerical values ranging from 0x8001 … 0x7FFF are scaled on the output current ranging from −10 V … +10 V. -
Page 34: Mounting
750-557/040-000 4AO +/-10V DC /XTR Mounting Mounting Sequence Fieldbus couplers, controllers and I/O modules of the WAGO-I/O-SYSTEM 750 are snapped directly on a carrier rail in accordance with the European standard EN 60175 (DIN 35). The reliable positioning and connection is made using a tongue and groove system. -
Page 35: Inserting And Removing Devices
WAGO-I/O-SYSTEM 750 XTR Mounting 750-557/040-000 4AO +/-10V DC /XTR Inserting and Removing Devices Do not touch hot surfaces! The surface of the housing can become hot during operation. If the device was operated at high ambient temperatures, allow it to cool off before touching it. -
Page 36: Removing The I/O Module
Mounting WAGO-I/O-SYSTEM 750 XTR 750-557/040-000 4AO +/-10V DC /XTR Press the I/O module into the assembly until the I/O module snaps into the carrier rail. Figure 8: Snap the I/O Module into Place (Example) With the I/O module snapped in place, the electrical connections for the data contacts and power jumper contacts (if any) to the fieldbus coupler/controller or to the previous or possibly subsequent I/O module are established. -
Page 37: Connect Devices
Only one conductor may be connected to each CAGE CLAMP Do not connect more than one conductor at one single connection! If more than one conductor must be routed to one connection, these must be connected in an up-circuit wiring assembly, for example using WAGO feed- through terminals. ®... -
Page 38: Connection Example
I/O module can be achieved even in the presence of interference acting on the signal cable. For further information about shielding, see system manual WAGO-I/O-SYSTEM 750 XTR, section “Connect Devices” > … > “Shielding.”... -
Page 39: Use In Hazardous Environments
Use in Hazardous Environments 750-557/040-000 4AO +/-10V DC /XTR Use in Hazardous Environments The WAGO-I/O-SYSTEM 750 (electrical equipment) is designed for use in Zone 2 hazardous areas and shall be used in accordance with the marking and installation regulations. The following sections include both the general identification of components (devices) and the installation regulations to be observed. -
Page 40: Marking Configuration Examples
Use in Hazardous Environments WAGO-I/O-SYSTEM 750 XTR 750-557/040-000 4AO +/-10V DC /XTR Marking Configuration Examples 7.1.1 Marking for Europe According to ATEX and IECEx Figure 12: Marking Example According to ATEX and IECEx Figure 13: Text Detail – Marking Example According to ATEX and IECEx Manual Version 1.3.0... -
Page 41: Table 22: Description Of Marking Example According To Atex And Iecex
WAGO-I/O-SYSTEM 750 XTR Use in Hazardous Environments 750-557/040-000 4AO +/-10V DC /XTR Table 22: Description of Marking Example According to ATEX and IECEx Marking Description TUEV 07 ATEX 554086 X Approving authority resp. certificate numbers IECEx TUN 09.0001 X Dust... -
Page 42: Figure 14: Marking Example For Approved Ex I I/O Module According To Atex And Iecex
Use in Hazardous Environments WAGO-I/O-SYSTEM 750 XTR 750-557/040-000 4AO +/-10V DC /XTR Figure 14: Marking Example for Approved Ex i I/O Module According to ATEX and IECEx Figure 15: Text Detail – Marking Example for Approved Ex i I/O Module According to ATEX and... -
Page 43: Table 23: Description Of Marking Example For Approved Ex I I/O Module According To Atex And Iecex
WAGO-I/O-SYSTEM 750 XTR Use in Hazardous Environments 750-557/040-000 4AO +/-10V DC /XTR Table 23: Description of Marking Example for Approved Ex i I/O Module According to ATEX and IECEx Marking Description TUEV 12 ATEX 106032 X Approving authority resp. certificate numbers... -
Page 44: Marking For The United States Of America (Nec) And Canada (Cec)
Use in Hazardous Environments WAGO-I/O-SYSTEM 750 XTR 750-557/040-000 4AO +/-10V DC /XTR 7.1.2 Marking for the United States of America (NEC) and Canada (CEC) Figure 16: Marking Example According to NEC Figure 17: Text Detail – Marking Example According to NEC 500... -
Page 45: Figure 18: Text Detail - Marking Example For Approved
WAGO-I/O-SYSTEM 750 XTR Use in Hazardous Environments 750-557/040-000 4AO +/-10V DC /XTR Figure 18: Text Detail – Marking Example for Approved Ex i I/O Module According to NEC 505 Table 25: Description of Marking Example for Approved Ex i I/O Module According to NEC 505... -
Page 46: Figure 20: Text Detail - Marking Example For Approved
Use in Hazardous Environments WAGO-I/O-SYSTEM 750 XTR 750-557/040-000 4AO +/-10V DC /XTR Figure 20: Text Detail – Marking Example for Approved Ex i I/O Modules According to CEC 18 attachment J Table 27: Description of Marking Example for Approved Ex i I/O Modules According to CEC 18... -
Page 47: Installation Regulations
WAGO-I/O-SYSTEM 750 XTR Use in Hazardous Environments 750-557/040-000 4AO +/-10V DC /XTR Installation Regulations For the installation and operation of electrical equipment in hazardous areas, the valid national and international rules and regulations which are applicable at the installation location must be carefully followed. - Page 48 Use in Hazardous Environments WAGO-I/O-SYSTEM 750 XTR 750-557/040-000 4AO +/-10V DC /XTR Explosive atmosphere occurring simultaneously with assembly, installation or repair work must be ruled out. Among other things, these include the following activities • Insertion and removal of components •...
-
Page 49: Special Notes Regarding Ansi/Isa Ex
WAGO-I/O-SYSTEM 750 XTR Use in Hazardous Environments 750-557/040-000 4AO +/-10V DC /XTR 7.2.2 Special Notes Regarding ANSI/ISA Ex For ANSI/ISA Ex acc. to UL File E198726, the following additional requirements apply: • Use in Class I, Division 2, Group A, B, C, D or non-hazardous areas only •... -
Page 50: List Of Figures
List of Figures WAGO-I/O-SYSTEM 750 XTR 750-557/040-000 4AO +/-10V DC /XTR List of Figures Figure 1: View ....................17 Figure 2: Data Contacts ..................18 Figure 3: Power Jumper Contacts ..............19 ® Figure 4: CAGE CLAMP Connectors ..............20 Figure 5: Display Elements.................21 Figure 6: Schematic Diagram ................22... -
Page 51: List Of Tables
WAGO-I/O-SYSTEM 750 XTR List of Tables 750-557/040-000 4AO +/-10V DC /XTR List of Tables Table 1: Number Notation ................... 8 Table 2: Font Conventions .................. 8 Table 3: Legend for Figure “View” ..............17 Table 4: Legend for Figure “Power Jumper Contacts” ........19 Table 5: Legend for Figure “CAGE CLAMP... - Page 52 Pos: 47 /Do kumentation allgemein/Einband/E inband Rüc kseite - alle Do kumente; CI 201 7 @ 28\mod_148 647750 3580_2 1.docx @ 4053 94 @ @ 1 WAGO Kontakttechnik GmbH & Co. KG • Postfach 2880 D - 32385 Minden Hansastraße 27 • D - 32423 Minden +49 571 887 –...
Need help?
Do you have a question about the 750-557/040-000 and is the answer not in the manual?
Questions and answers