Danfoss AK-CC55 Compact Installation Manual page 13

Compact - continued
Replace the controller's factory settings with the
present settings
Rail heat control
0=not used, 1=pulse control with timer function (o41
and o42), 2=pulse control with dew point function A
Dew point value where the rail heat is minimum
Dew point value where the rail heat is 100% on
Lowest permitted rail heat effect in %
Time delay from "open door" until refrigeration is
started
Fan operation at stopped cooling (forced closing):
0= Stopped (defrost allowed)
1= Running (defrost allowed)
2= Stopped (defrost not allowed)
3= Running (defrost not allowed)
Light and night blinds defined:
0: Light is switched off and night blind is opened
when the main switch is off
1: Light and night blinds are independent of main
switch
Configuration of alarm relay:
The alarm relay will be activated by an alarm in one or
more of the following priorities.
Setting:
0 = The relay is not activated by alarms
1 = Only high priority alarms
2 = High and medium priority alarms
3 = High, medium and low priority alarms
Max. opening time of night blinds after a manual
override with DI activation.
Stop time for fans while the night blinds roll down
Cycle time for rail heat at PWM on AO1
User defined refrigerant 3-digit Rfg. factor K1
User defined refrigerant 3-digit Rfg. factor K2
User defined refrigerant 3-digit Rfg. factor K3
Max. limitation of the superheat reference when
regulated with liquid-filled evaporator
Min. limitation of the superheat reference when
regulated with liquid-filled evaporator
Access code 1 (simple access)
Locking of setting display
0 = display is never locked
1 = display is locked after 15 minutes of inactivity.
Display must be unlocked by pressing up and down
button simultaneously for 3 seconds.
Configuration of relay output DO2: 0=not used,
1=fan, 2=fan Eco, 3=defrost, 4=rail heat, 5=alarm,
6=light, 7=night blinds, 8=compressor, 9=compressor
2, 10=heating element
Configuration of relay output DO3: 0=not used,
1=fan, 2=fan Eco, 3=defrost, 4=rail heat, 5=alarm,
6=light, 7=night blinds, 8=compressor, 9=compressor
2, 10=heating element
Configuration of relay output DO4: 0=not used,
1=fan, 2=fan Eco, 3=defrost, 4=rail heat, 5=alarm,
6=light, 7=night blinds, 8=compressor, 9=compressor
2, 10=heating element
Configuration of analogue output AO1: 0=not used.
1=rail heat PWM
Manual control of output: AKV valve 0-100%
Manual control of output: Compressor1/LLSV
Manual control of output: Fan
Manual control of output: Defrost
Manual control of output: Rail heat
Manual control of output: Alarm
© Danfoss | DCS (vt) | 2019.10
R-W Code 1 2 3 4
3-3* o67 1 1 1 1
1-2 o85 1 1 1 1
1-2 o86 1 1 1 1
1-2 o87 1 1 1 1
1-2 o88 1 1 1 1
1-2 o89 1 1 1 1
1-2 o90 1 1 1 1
1-2 o98 1 1
1-2 P41 1 1 1 1
1-2 P60 1
1-2 P65 1
1-2 P82 1 1 1 1
1-3* P83
1-3* P84
1-3* P85
1-2 P86
1-2 P87
1-1 P88 1 1 1 1
1-2 P89 1 1 1 1
1-3* q02 1
1-3* q03 1
1-3* q04 1
1-3* q09 1 1 1 1
1-2** q11
1-2** q12 1 1 1 1
1-2** q13 1 1 1 1
1-2** q14 1 1 1 1
1-2** q15 1 1
1-2** q16 1 1
5 6 7 8 9 Min.
1 1 1 1 1 0/Off
1 1 1 1 1 0
1 1 1 1 1 -10°C
1 1 1 1 1 "o86"
1 1 1 1 1 0 %
1 1 1 1 1 0 min.
1 1 1 1 1 0
1 1 0
1 1 1 1 1 0
1 0 min.
1 0 sec
1 1 1 1 1 4 sec
1 1 1 1 1 -999
1 1 1 1 1 -999
1 1 1 1 1 -999
1 1 1 1 1 "P87"
1 1 1 1 1 0°C
1 1 1 1 1 0
1 1 1 1 1 0/Off
1 0
1 0
1 0
1 1 1 1 1 0
1 1 1 1 1 0 %
1 1 0/Off
1 1 1 1 1 0/Off
1 1 1 1 1 0/Off
1 1 0/Off
1 1 0/Off
AN300028324304en-000401 | 13
Max. Fac. Actual
1/On 0/Off
2 0
"o87" 8
50°C 17
100 % 30
240 min. 30
3 1
1 0
3 2
60 min. 5
300 sec 0
60 sec 10
999 300
999 300
999 300
20°C 3
"P86" 1
999 0
1/On 0/Off
10 0
10 0
10 0
1 0
100 % 0
1/On 0/Off
1/On 0/Off
1/On 0/Off
1/On 0/Off
1/On 0/Off