TC Electronic FINALIZER Service Manual
  1. Manuals
  2. Brands
  3. TC Electronic Manuals
  4. Computer Hardware
  5. Finalizer
  6. Service manual

TC Electronic FINALIZER Service Manual

Hide thumbs Also See for FINALIZER:
Table of Contents

Advertisement

Quick Links

OVERLOAD
POWER
48000Hz
44100Hz
32000Hz
MIDI IN
C ARD
WORKING
EDITED
TC Electronic A/S, Sindalsvej 34, DK-8240 Risskov, DENMARK Telephone: +45 8621 7599 Fax: +45 8621 7598 Email: tc@tcelectronic.com WWW: http://www.tcelectronic.com
FINALIZER
Service Manual
2nd Edition
O U T P U T
L
dB
-60
-48
-44
-40
-36
-32
-30
-28
-26
-24
-22
-20
-18
-16
R
E X P
N o rm alizer LIM
H igh
IN P U T
L
M id
-60
-40
-30
-24
-18
-12
-9
-6
-3
-0
dB
R
Lo w
FUNCTIONS
SO FT C LIP
MAIN PAGE
WIZARD
-14
-12
-10
-8
-6
-5
-4
-3
-2
-1 -0.5
0
TOOLS
dB
G A IN R ED U C T IO N
L IM
QUICK STORE
-18
-14
-10
-8
-6
-4
-3
-2
-1
-0.5
WIZARD
-18
-14
-10
-8
-6
-4
-3
-2
-1
-0.5
UTILITY
PROGRAM
CONTROL
RECALL
HELP
BLOCK ON/OFF
STORE
BLOCK
COMPARE
BAND
BYPASS
U N I T Y G A IN
PARAMETER
MENU
ADJUST

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the FINALIZER and is the answer not in the manual?

Questions and answers

Related Manuals for TC Electronic FINALIZER

Summary of Contents for TC Electronic FINALIZER

  • Page 1 M id WORKING BAND -0.5 EDITED Lo w UTILITY BYPASS U N I T Y G A IN PARAMETER MENU TC Electronic A/S, Sindalsvej 34, DK-8240 Risskov, DENMARK Telephone: +45 8621 7599 Fax: +45 8621 7598 Email: tc@tcelectronic.com WWW: http://www.tcelectronic.com...

  • Page 2: Table Of Contents

    Test Point Values:....................15 LED Error Codes:....................17 Jumper settings:....................17 Software Changes: ....................18 2nd Edition © Copyright 1997, TC Electronic A/S. All rights reserved. Technical Specifications: ..................19 Filename: FINSMAN2.DOC Cable Specifications: ....................20 Stock number: 605 0290 11 Appendix list: Flow chart, Schematics, Part lists, PCB Lay-out ......21...

  • Page 3: Introduction

    The Block diagram for the signal flow in the Finalizer shows the order of all the effects. Part lists contain a column called TCcode. Use this code when ordering spare parts.

  • Page 4: Quick Trouble Shooting

    If SAMPLE RATE is set to 44.1KHz and the digital input signal is 48KHz (or vice versa), distortion will appear. The Finalizer cannot do real sample conversion! Cannot turn power off with power switch at front The switch must be pressed for at least 1 second to turn off power.

  • Page 5: Built-In Test Program

    Built-in Test Program: The Finalizer has a Built-in Test Program. To run the program; Press the BYPASS button while powering on. Use the cursor to select RUN TEST PROGRAM. Press OK and follow the instructions on the display. To leave the Built-in Test Program; turn off the power.

  • Page 6: Disassembly Procedure For Main Board

    Desolder the seven wires from power supply. main board Power Supply Top view Fig. 3: Screws at back panel. MIDI / RS485 PROFESSIONAL AUDIO EQUIPMENT LISTED 5D83 3 screws 3 screws 3 screws 1 screw Jack nut __________________________________________________________________________________________________________________________________________________________________________________________________ TC Electronic A/S Finalizer Service manual page 6...

  • Page 7: Disassembly Procedure For Front Section

    At the end with ADJUST , pull out the two white front board guides. Opening up the profile a little will lighten the pressure at the guides, see fig. 5. __________________________________________________________________________________________________________________________________________________________________________________________________ TC Electronic A/S Finalizer Service manual page 7...

  • Page 8: Exchange Of Power Supply Module

    Remove the power supply by removing one screw at the back panel, just below the mains plug, see fig. 6. Mount the new power supply with the screw at the back panel. __________________________________________________________________________________________________________________________________________________________________________________________________ TC Electronic A/S Finalizer Service manual page 8...

  • Page 9: Exchange Of Battery

    Lithiumbatteri. Eksplosionsfare ved fejlagtig håndtering. Må kun udskiftes med batteri af samme fabrikat og type. Lever det brugte batteri tilbage til leverandøren. Recommended battery type: CR2032. TC stock no. (TCcode) for battery: 342 0000 11 __________________________________________________________________________________________________________________________________________________________________________________________________ TC Electronic A/S Finalizer Service manual page 9...

  • Page 10: Block Diagram

    Block Diagram: The block diagram in figure 7 gives a quick view of the signal flow in the Finalizer. As the block diagram shows the input and output sections will always be active, even in Bypass mode. The AES/EBU and the SPDIF inputs are connected internally. Therefore, do not connect cables to both AES/EBU and the SPDIF inputs at the same time.
  • Page 11 Fig. 7: Block diagram for the Finalizer __________________________________________________________________________________________________________________________________________________________________________________________________ TC Electronic A/S Finalizer Service manual page 11...

  • Page 12: Circuit Description

    Circuit Description: The Finalizer consist of a front, a digital, an analog and a power supply section. Here is a brief description of the sections: Front section consist of three boards and a display, all placed in the front profile.

  • Page 13: Power On Sequence

    Power On Sequence: The table below shows the Power On Sequence for main board version PC12001-3, when the Finalizer is switched on by using the power switch at the back panel. Equal sequence numbers mean that the events are independent of each other. Column Trouble Shooting has hints about what to check if the event fails.
  • Page 14 TP11, ASIC clock starts up, 80MHz IC10 + soldering Picture with user information and software version appears on the display. Front connection, display, RECALL picture appears on the display. Application software, __________________________________________________________________________________________________________________________________________________________________________________________________ TC Electronic A/S Finalizer Service manual page 14...

  • Page 15: Test Point Values

    44100Hz or 48000Hz. Data signal DA-data. Data signal AD-data. 10Vpp, 0VDC Left input amp. Running Built-in Test program, Option: analog 10Vpp, 0VDC Right input amp. Running Built-in Test program, Option: analog __________________________________________________________________________________________________________________________________________________________________________________________________ TC Electronic A/S Finalizer Service manual page 15...
  • Page 16 +3.1VDC 10Vpp, balanced, max. 10mVDC, Left output connector Running Built-in Test program, Option: analog THD+N: <0.01% 10Vpp, balanced, max. 10mVDC Right output connector Running Built-in Test program, Option: analog THD+N: <0.01% __________________________________________________________________________________________________________________________________________________________________________________________________ TC Electronic A/S Finalizer Service manual page 16...

  • Page 17: Led Error Codes

    Boot sector in Flash is corrupted. Reload boot or replace Flash Jumper settings: Jumper settings on main board version PC12001-3: JP2 unused. JP4 & JP5 controls boot mode: Boot from Flash (normal mode) Boot from PCMCIA (only used at factory) __________________________________________________________________________________________________________________________________________________________________________________________________ TC Electronic A/S Finalizer Service manual page 17...

  • Page 18: Software Changes

    Software Changes: Listed below are changes in the application software for the Finalizer. Filename for application software is FINvxxx.wiz (xxx represents the version no.) Changes from version 1.05 to 1.08: Updating from 1.05 to 1.08 will not affect the presets.

  • Page 19: Technical Specifications

    Storage Temperature: -22 °F 167 °F (-30 °C to 70 °C) Sample Rates: 32 kHz, 44.1 kHz, 48 kHz Humidity: Max. 95% non-condensing Note: All specifications are subject to change without notice __________________________________________________________________________________________________________________________________________________________________________________________________ TC Electronic A/S Finalizer Service manual page 19...

  • Page 20: Cable Specifications

    Note: Pin 1 and 3 at the Finalizer are reserved for optional RS485 interface Therefore, use only 3-wires if the Finalizer is connected to other equipment that use these pins FADER CABLE JACK PLUG max. 100m...

  • Page 21: Appendix List: Flow Chart, Schematics, Part Lists, Pcb Lay-Out

    3 pages Part list for Front boards ver. PC12502-3 6 pages PCB lay-out for Front boards ver. PC12502-2 & 1 page PC12502-3 Part list for mechanical parts in Finalizer 2 pages __________________________________________________________________________________________________________________________________________________________________________________________________ TC Electronic A/S Finalizer Service manual page 21...

Table of Contents