Related Manuals for Clarke CIG81224
Summary of Contents for Clarke CIG81224
- Page 1 INSTANT GARAGE MODEL NO: CIG81224 PART NO: 3503578 ASSEMBLY INSTRUCTIONS ORIGINAL INSTRUCTIONS GC1117...
-
Page 2: Safety Instructions
INTRODUCTION Thank you for purchasing this CLARKE Instant Garage. When erected, the CIG81224 garage will be of the dimensions show below. Weight is 87kg packed (83.5 kg unpacked). Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. - Page 3 Choose your garage's location carefully. Check for overhead utility lines, branches, etc. DO NOT install near roofs or other structures that may shed snow, ice or excessive run-off onto your shelter. Keep away from power cables. Erect your garage on a level surface. Have an overview of all parts before attempting installation.
-
Page 4: Component Parts List
COMPONENT PARTS LIST Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... - Page 5 ASSEMBLY WARNING: DO NOT PLACE THE GARAGE UNDER TREES FROM WHICH HARD FRUIT SUCH AS APPLES, WALNUTS OR HEAVY PINE CONES, ETC., MAY FALL. KEEP CHILDREN AWAY DURING ASSEMBLY. THIS PRODUCT CONTAINS SMALL PARTS WHICH CAN BE SWALLOWED BY CHILDREN. DO NOT ATTEMPT TO ASSEMBLE THE PRODUCT IF ANY PARTS ARE MISSING, WARNING: AT LEAST 3 PEOPLE ARE NEEDED TO COMPLETE THE ASSEMBLY AS SOME OF THE STEPS REQUIRE HEAVY LIFTING.
- Page 6 STEP 1: PREPARING THE ROOF PARTS Select a suitable location for the garage. The layout of the roof parts is shown in Diagram B. Note the differences between the connectors shown in Diagram C. (connectors are also individually numbered). Note: When installed, the welded socket for the cross rail must be below the bend.
- Page 7 STEP 2: ASSEMBLING THE ROOF 1. Assemble the roof frame by connecting the parts layout above. NOTE: The hole end on Part #3 needs to be connected to Parts #12 and #7 (See Diagram D1& D2) by the fittings #21, #23 and #24. There is a spring button on both ends of Part #4.
-
Page 8: Step 3: Attaching The Legs
STEP 3: ATTACHING THE LEGS 1. There are 14 legs for the whole shelter. Follow Drawing E1. Connect the tubes #1 & #10 to create the 4 corner legs. 2. Connect tubes #1 & #2 to create the 10 center legs. 3. - Page 9 STEP 4: SQUARE AND ANCHOR THE FRAME 1. Check the measurements of the frame are 12’ at both the front and back corners, as well as across the center. 2. Take a diagonal measurement as shown in Diagram F. When these two measures are equal the frame is square.
- Page 10 STEP 5: INSTALLING THE FRONT AND BACK COVERS The front cover has a zippered door to allow entry to the garage. Be sure to locate this cover at the desired end and ensure the zipper is in the closed position while installing. The back cover is a solid piece of polyethylene.
- Page 11 3. Disconnect the tube #4 from the connector #12 with a rubber mallet. Wrap the door panel around the tube. Slip the webbing strap between the tubes and then re-connect. Repeat for all the shoulders. 4. Hook the pre-assembled ratchet tie-down to the bent corner leg and tighten the ratchet until the front door cover is reasonably tight.
- Page 12 STEP 6: INSTALLING THE MAIN COVER 1. Lay the cover on the ground next to the frame with the inside of the cover (the side with the pockets) facing down and the strap on the front and rear of the frame. 2.
- Page 13 Note: Over-tightening can cause damage to straps and/or the anchor point. Do not over-tighten! The garage is now ready for use. Note: Check periodically (two to three times in the first week and tighten ratchet tie-downs and all hardware as needed. Monthly inspection is recommended throughout usage.
- Page 14 DISASSEMBLY When disassembling the garage depress the spring-loaded bar to disengage the ratchet and open the ratchet handle completely to allow the webbing strap to pull through. PLEASE RE-READ ALL WARNINGS CONTAINED ON PAGE 2/3 OF THESE INSTRUCTIONS. SAVE THESE INSTRUCTIONS FOR FUTURE USE. To dismantle, execute all instructions in reverse order.
- Page 15 GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase. This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.
Need help?
Do you have a question about the CIG81224 and is the answer not in the manual?
Questions and answers