Related Manuals for Clarke CIS81212
Summary of Contents for Clarke CIS81212
- Page 1 INSTANT SHED MODEL NO: CIS81212 (12 X 12 X 8’) PART NO: 3503584 ASSEMBLY INSTRUCTIONS ORIGINAL INSTRUCTIONS GC01/21...
-
Page 2: Safety Warnings
INTRODUCTION Thank you for purchasing this CLARKE Instant Shed. Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. In doing so you will ensure the safety of yourself and that of others around you, and you can look forward to your purchase giving you long and satisfactory service. -
Page 3: Siting The Garage
POSITIONING AND INSTALLATION OF THE SHED POSITIONING THE SHED This shed is a temporary structure and is not recommended as a permanent building. It is designed to offer protection from sun, rain, light snow, tree sap and bird droppings etc. It is not designed to shelter equipment from excessively high winds or heavy snow. -
Page 4: Using The Storage Space
A supply of fresh air through the doorway will at least partly remove this issue. For long term storage of moisture sensitive belongings in all weathers, the use of a Dehumidifier may be required, such as those in the Clarke range. A suitable extension lead to a locally available power supply will be required. -
Page 5: Component Parts List
COMPONENT PARTS LIST Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... - Page 6 ASSEMBLY WARNING: DO NOT PLACE THE PRODUCT UNDER TREES FROM WHICH HARD FRUIT SUCH AS APPLES, WALNUTS OR HEAVY PINE CONES, ETC MAY FALL. KEEP CHILDREN AWAY DURING ASSEMBLY. THIS PRODUCT CONTAINS SMALL PARTS WHICH CAN BE SWALLOWED BY CHILDREN. DO NOT ATTEMPT TO ASSEMBLE THE PRODUCT IF ANY PARTS ARE MISSING.
- Page 7 step 1: preparing the roof parts Select a suitable location for the garage. The layout of the roof parts is shown in Diagram B. Note the differences between the connectors shown in Diagram C. (Connectors are also individually numbered). Note: When installed, the welded socket for the cross rail must be below the bend.
- Page 8 STEP 2: ASSEMBLING THE ROOF 1. Assemble the roof frame by connecting the parts layout above. 2. Connect one end of Part #5 with Part #4 using the spring button. 3. Connect the other end of Part#5 with Parts #12 & #13 (See Diagram D1 & D2) by the fittings #22, #24 &...
-
Page 9: Step 3: Attaching The Legs
STEP 3: ATTACHING THE LEGS There are 8 legs for the whole shelter. 1. Follow figure E1. Connect the tubes #1,#3 & #10 to create the 4 corner legs. 2. Connect tubes #1 & #2 to create the 4 center legs. 3. - Page 10 STEP 4: SQUARE AND ANCHOR THE FRAMES WARNING: SERIOUS INJURY TO PERSONS OR PROPERTY COULD RESULT IF THE GARAGE IS NOT SECURELY ANCHORED WITH EITHER THE GROUND ANCHORS SUPPLIED, OR IF SITED ON CONCRETE OR TARMAC, USE SUITABLE SUBSTANTIAL GROUND ANCHOR BOLTS. 1.
- Page 11 STEP 5: INSTALLING THE FRONT AND BACK COVERS The front cover has a zippered door to allow entry to the shelter. Be sure to locate this cover at the desired end and ensure the zipper is in the closed position while installing. The back cover is a solid piece of fabric.
- Page 12 3. Following figure J1,disconnect the tube (#5,#6) from the connector (#12,#8, ＆ #9) 4. Slip the webbing strap between the tube #6 and the connector as shown and reconnect the tubes. 5. Repeat this for the opposite shoulder. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 13 6. Move to the apex of the garage using a step ladder and using a rubber mallet, disconnect the apex tube (#6) from the connector (#12). Slip the webbing strap between the tubes (see Diagram K2) and reconnect. 7. While one person remains on the steps and standing at the apex of the garage, the other person inserts the hook of the ratchet starps into both sides of the corner legs at (K3).
- Page 14 6. Slide the bottom cross rails through the fabric pockets at each leg and re- attach with clamps at each leg. Repeat this on the other side. Push down on the cover rails to tighten the cover before tightening all bolts fully. 7.
- Page 15 This can take the form of an additional Auger Securing Set GA1 (already supplied with Clarke instant garages), which can add greater security for exposed, windy locations. Alternatively, the Easy Hook Anchoring System GHA2, can be used to provide greater security on soft ground, available from your Clarke dealer.