Related Manuals for Clarke CIG91015
Summary of Contents for Clarke CIG91015
- Page 1 INSTANT GARAGE MODEL NO: CIG91015 PART NO: 3503590 ASSEMBLY INSTRUCTIONS ORIGINAL INSTRUCTIONS GC0621...
-
Page 2: Safety Warnings
When erected, the CIG91015 garage will be of the dimensions show on page 4. The product weight is 52 kg packed (49.5 kg unpacked). -
Page 3: Positioning And Installation Of The Garage
POSITIONING AND INSTALLATION OF THE GARAGE POSITIONING THE GARAGE This garage is a temporary structure and is not recommended as a permanent building. It is designed to offer protection from sun, rain, light snow, tree sap and bird droppings etc. It is not designed to shelter equipment from excessively high winds or heavy snow. -
Page 4: Using The Storage Space
A supply of fresh air through the doorway will at least partly remove this issue. For long term storage of moisture sensitive belongings in all weathers, the use of a Dehumidifier may be required, such as those in the Clarke range. A suitable extension lead to a locally available power supply will be required. -
Page 5: Component Parts List
COMPONENT PARTS LIST Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... - Page 6 ASSEMBLY WARNING: DO NOT PLACE THE PRODUCT UNDER TREES FROM WHICH HARD FRUIT SUCH AS APPLES, WALNUTS OR HEAVY PINE CONES, ETC., MAY FALL. KEEP CHILDREN AWAY DURING ASSEMBLY. THIS PRODUCT CONTAINS SMALL PARTS WHICH CAN BE SWALLOWED BY CHILDREN. DO NOT ATTEMPT TO ASSEMBLE THE PRODUCT IF ANY PARTS ARE MISSING.
- Page 7 STEP 1: PREPARING THE ROOF PARTS Select a suitable location for the garage. The layout of the roof parts is shown in diagram B. Note the differences between the connectors shown in Diagram C. (connectors are also individually numbered). Note: When installed, the welded socket for the cross rail must be below the bend.
- Page 8 STEP 2: ASSEMBLING THE ROOF 1. Assemble the roof frame by connecting the parts layout above. NOTE: The hole end on Part #3 needs to be connected to Parts #12 and #13 (See Diagram D1& D2) by the fittings #22, #24 and #25. •...
-
Page 9: Step 3: Attaching The Legs
STEP 3: ATTACHING THE LEGS There are 10 legs for the whole garage. 1. Follow Drawing E. Connect the leg tubes #1, #2 & #6 to create the 4 x corner legs. 2. Connect leg tubes #1 & #4 to create the 6 x center legs. 3. - Page 10 STEP 4: SQUARE AND ANCHOR THE FRAME WARNING: SERIOUS INJURY TO PERSONS OR PROPERTY COULD RESULT IF THE GARAGE IS NOT SECURELY ANCHORED, WITH EITHER THE GROUND ANCHORS SUPPLIED OR IF SITED ON CONCRETE OR TARMAC USE SUITABLE SUBSTANTIAL GROUND ANCHOR BOLTS. 1.
- Page 11 STEP 5: INSTALLING THE FRONT AND BACK COVERS The front cover has a zippered door to allow entry to the garage. Be sure to locate this cover at the desired end and ensure the zipper is in the fully closed position while installing.
- Page 12 Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 13 4. Repeat this with the tubes at each shoulder of the frame, wrapping the edges of the door panel around the tubes and re-connecting the frame components. 5. Hook the pre-assembled ratchet tie-down to the corner bottom (#6) and tighten the ratchet until the door cover is reasonably tight. 6.
- Page 14 7. When the cover rails are all secured, tighten the end covers and the main cover to the end frames using the ratchet action. This should always be done with the front door panel closed. NOTE: Over-tightening can cause damage to the end cover pockets.
- Page 15 This can take the form of an additional Auger Securing Set GA2 (already supplied with Clarke Instant Garages), which can add greater security for exposed, windy locations. Alternatively the Easy Hook Anchoring System GHA2, can be used to provide greater security on soft ground.