Related Manuals for Clarke CIG81015
Summary of Contents for Clarke CIG81015
-
Page 1: Assembly Instructions
INSTANT GARAGE MODEL NO: CIG81015 PART NO: 3503570 ASSEMBLY INSTRUCTIONS ORIGINAL INSTRUCTIONS GC12/18 ISS 3... -
Page 2: Safety Warnings
INTRODUCTION Thank you for purchasing this CLARKE Instant Garage. When erected, the CIG81015 garage will be of the dimensions shown on page 4. Weight is 52kg packed (50 kg unpacked). Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. -
Page 3: Positioning And Installation Of The Garage
POSITIONING AND INSTALLATION OF THE GARAGE POSITIONING THE GARAGE This garage is a temporary structure and is not recommended as a permanent building. It is designed to offer protection from sun, rain, light snow, tree sap and bird droppings etc. It is not designed to shelter equipment from excessively high winds or heavy snow. -
Page 4: Using The Storage Space
A supply of fresh air through the doorway will at least partly remove this issue. For long term storage of moisture sensitive belongings in all weathers, the use of a dehumidifier may be advantageous, such as those in the Clarke catalogue. A suitable extension lead to a locally available power supply will be required. -
Page 5: Component Parts List
COMPONENT PARTS LIST Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... - Page 6 ASSEMBLY WARNING: DO NOT PLACE THE PRODUCT UNDER TREES FROM WHICH HARD FRUIT SUCH AS APPLES, WALNUTS OR HEAVY PINE CONES, ETC., MAY FALL. KEEP CHILDREN AWAY DURING ASSEMBLY. THIS PRODUCT CONTAINS SMALL PARTS WHICH CAN BE SWALLOWED BY CHILDREN. DO NOT ATTEMPT TO ASSEMBLE THE PRODUCT IF ANY PARTS ARE MISSING.
- Page 7 STEP 1: PREPARING THE ROOF PARTS Select a suitable location for the garage. The layout of the roof parts is shown in diagram B. Note the differences between the 5 connectors shown in Diagram C. (connectors are also individually numbered). Note: When installed, the welded socket for the cross rail must be below the bend.
- Page 8 STEP 2: ASSEMBLING THE ROOF 1. Assemble the roof frame by connecting the parts layout above. NOTE: The hole end on Part #3 needs to be connected to Parts #12 and #13 (See Diagram D1& D2) by the fittings #22, #24 and #25. There is a spring button on both ends of Part #5 &...
-
Page 9: Step 3: Attaching The Legs
STEP 3: ATTACHING THE LEGS There are 8 legs for the whole garage. 1. Follow Drawing E1. Connect the tubes #1,# 2 & #6 to create the 4 corner legs. 2. Connect tubes #1 & #4 to create the 4 center legs. 3. - Page 10 STEP 4: SQUARE AND ANCHOR THE FRAMES 1. Check the measurements of the frame are 10’ at both the front and back corners, as well as across the center. 2. Take a diagonal measurement as shown in Diagram F. When these two measures are equal the frame is square.
- Page 11 STEP 5: INSTALLING THE FRONT AND BACK COVERS The front cover has a zippered door to allow entry to the garage. Be sure to locate this cover at the desired end and ensure the zipper is in the closed position while installing. The back cover is a solid piece of polyethylene.
- Page 12 3. Using a rubber mallet, disconnect the apex tube (#4A) from the connector (#12) located between the leg and the roof tubes. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 13 4. Slip the webbing strap between tube #5 and the connector (as shown in Diagram I). Rejoin the tubes. 5. Repeat this step for the opposite shoulder. 6. Move to the apex of the garage using a step ladder and using a rubber mallet, disconnect the apex tube (#4a) from the connector (#12).
- Page 14 3. Pull the cover over the frame with the help of the rope as in Diagram J, making sure to center the cover on the frame. There should be an equal amount overhanging at all four corners. 4. Assemble the ratchet straps (Part #29) to the web ends on the four corners of the cover, one for each corner.
- Page 15 DISASSEMBLY When disassembling the garage depress the spring-loaded bar to disengage the ratchet and open the ratchet handle completely to allow the webbing strap to pull through. PLEASE RE-READ ALL WARNINGS CONTAINED ON PAGE 2/3 OF THESE INSTRUCTIONS. SAVE THESE INSTRUCTIONS FOR FUTURE USE. To dismantle, execute all instructions in reverse order.