Subscribe to Our Youtube Channel
Related Manuals for Clarke CIS788
Summary of Contents for Clarke CIS788
- Page 1 INSTANT GARAGE MODEL NO: CIS788 PART NO: 3503582 ASSEMBLY INSTRUCTIONS ORIGINAL INSTRUCTIONS GC0918...
-
Page 2: Safety Instructions
INTRODUCTION Thank you for purchasing this CLARKE Instant Garage. When erected, the CIS788 garage will be of the dimensions show below. Weight is 34 kg packed (32 kg unpacked). Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. - Page 3 Erect your garage on a level surface. Have an overview of all parts before attempting installation. Make sure all components are available. DO NOT use this product in environments for which it is not Intended (i.e. extreme cold, high winds, extreme heat, heavy rainfall, etc). Always wear safety glasses when assembling this product.
-
Page 4: Component Parts List
COMPONENT PARTS LIST Description Illustration Upright Pole with Dimples Corner Extension Tube Bent Corner Leg Shoulder Cross Rail Rafter Pole Bottom Cross Rail Center Extension Tube 3-Way Side Connector - Left 3-Way Side Connector - Right 4-Way Side Connector 3-Way Peak Connector 4-Way Peak Connector 4-Way Cross Rail Clamp 3-Way Cross Rail Clamp... - Page 5 ASSEMBLY 1. Place all parts from the packaging in a clear area and arrange them on the ground in front of you. 2. Remove all packaging materials and place them back in the box. Do not dispose of the packaging materials until assembly is complete. 3.
- Page 6 STEP 1: PREPARING THE ROOF PARTS Select a suitable location for the garage. The layout of the roof parts is shown in Diagram B. Diagram B Note the differences between the connectors shown in Diagram C. (connectors are also individually numbered). Note: When installed, the welded socket for the cross rail must be below the bend.
- Page 7 STEP 2: ASSEMBLING THE ROOF Diagram D Attach the shoulder cross rails (4) to the 3-way side connectors (8, 9) and 4-way side connectors (10). Insert the connectors (8, 9, 10) into the rafter poles (5) to complete the assembly of the roof (Diagram D). NOTE: ●...
-
Page 8: Step 3: Attaching The Legs
STEP 3: ATTACHING THE LEGS There are 6 legs for the whole shelter. 1. Follow Diagram E. Connect the tubes #1,2 & #3 to create the 4 corner legs. 2. Connect tubes #1 & #7 to create the 2 center legs. Diagram E 3. - Page 9 STEP 4: SQUARE AND ANCHOR THE FRAMES 1. Check that the width measurements of the frame are 8' at both the front and back corners, as well as across the center. Diagram F 2. Take a diagonal measurement as shown in Diagram F. When these two measures are equal the frame is square.
- Page 10 STEP 5: INSTALLING THE FRONT AND BACK COVERS The front cover has a zippered door to allow entry to the garage. Be sure to locate this cover at the desired end and ensure the zipper is in the closed position while installing. The back cover is a solid piece of fabric.
- Page 11 Diagram J Diagram J1 Diagram J2 Diagram J3 3. Following Diagram J1,disconnect the tube (#4) from the connector (#8,#9,＆ #11） 4. Wrap the door panel around the tube. Slip the webbing strap between the tubes and then re-connect. Diagram J2) 5.
- Page 12 STEP 6: INSTALLING THE MAIN COVER 1. Lay the cover on the ground next to the frame with the inside of the cover (the side with the pockets) facing down and the strap on the front and rear of the frame. 2.
- Page 13 Diagram L 7. When the cover rails are all secured, proceed to the four corners and tighten the end covers to the end frames using the ratchet action. Diagram M Note: Over-tightening can cause damage to straps and/or the anchor point. Do not over-tighten! The garage is now ready for use.
- Page 14 Note: Check periodically (two to three times in the first week) and tighten ratchet tie-downs and all hardware as needed. Monthly inspection is recommended throughout usage. DISASSEMBLY When disassembling the garage, depress the spring-loaded bar to disengage the ratchet and open the ratchet handle completely to allow the webbing strap to pull through.
- Page 15 GUARANTEE This product is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase. This guarantee is invalid if the product is found to have been abused or tampered with in any way, or not used for the purpose for which it was intended.
Need help?
Do you have a question about the CIS788 and is the answer not in the manual?
Questions and answers