Subscribe to Our Youtube Channel
Related Manuals for Clarke 3503578
Summary of Contents for Clarke 3503578
- Page 1 INSTANT GARAGE MODEL NO: CIG81224 PART NO: 3503578 ASSEMBLY INSTRUCTIONS ORIGINAL INSTRUCTIONS GC1120 - ISS 5...
-
Page 2: Safety Warnings
INTRODUCTION Thank you for purchasing this CLARKE Instant Garage. When erected, the CIG81224 garage will be of the dimensions show below. Weight is 85kg packed (82 kg unpacked). Before attempting to use this product, please read this manual thoroughly and follow the instructions carefully. -
Page 3: Positioning And Installation Of The Garage
POSITIONING AND INSTALLATION OF THE GARAGE POSITIONING THE GARAGE This garage is a temporary structure and is not recommended as a permanent building. It is designed to offer protection from sun, rain, light snow, tree sap and bird droppings etc. It is not designed to shelter equipment from excessively high winds or heavy snow. -
Page 4: Using The Storage Space
A supply of fresh air through the doorway will at least partly remove this issue. For long term storage of moisture sensitive belongings in all weathers, the use of a Dehumidifier may be required, such as those in the Clarke range. A suitable extension lead to a locally available power supply will be required. -
Page 5: Component Parts List
COMPONENT PARTS LIST Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com... - Page 6 ASSEMBLY WARNING: DO NOT PLACE THE GARAGE UNDER TREES FROM WHICH HARD FRUIT SUCH AS APPLES, WALNUTS OR HEAVY PINE CONES, ETC., MAY FALL. KEEP CHILDREN AWAY DURING ASSEMBLY. THIS PRODUCT CONTAINS SMALL PARTS WHICH CAN BE SWALLOWED BY CHILDREN. DO NOT ATTEMPT TO ASSEMBLE THE PRODUCT IF ANY PARTS ARE MISSING, WARNING: DO NOT LEAVE THE STRUCTURE UNATTENDED DURING ASSEMBLY IN CASE PERSONAL INJURY OR DAMAGE TO THE GARAGE...
- Page 7 STEP 1: PREPARING THE ROOF PARTS Select a suitable location for the garage. The layout of the roof parts is shown in Diagram B. Note the differences between the connectors shown in Diagram C. (connectors are also individually numbered). Note: When installed, the welded socket for the cross rail must be below the bend.
- Page 8 STEP 2: ASSEMBLING THE ROOF 1. Asemble the roof frame by connecting the parts layout above. 2. Connect one end of Part #5 with Part #4 using the spring button. 3. Connect the other end of Part #5 with Parts #12 and #13 (See Diagram D1& D2) with the fittings #22, #24 and #25.
-
Page 9: Step 3: Attaching The Legs
STEP 3: ATTACHING THE LEGS 1. There are 14 legs for the whole shelter. Follow Drawing E1. Connect the tubes #1, 3 & #10 to create the 4 corner legs. 2. Connect tubes #1 & #2 to create the 10 center legs. 3. - Page 10 STEP 4: SQUARE AND ANCHOR THE FRAME WARNING: SERIOUS INJURY TO PERSONS OR PROPERTY COULD RESULT IF THE GARAGE IS NOT SECURELY ANCHORED, WITH EITHER THE GROUND ANCHORS SUPPLIED OR IF SITED ON CONCRETE OR TARMAC USE SUITABLE SUBSTANTIAL GROUND ANCHOR BOLTS. 1.
- Page 11 STEP 5: INSTALLING THE FRONT AND BACK COVERS The front cover has a zippered door to allow entry to the garage. Be sure to locate this cover at the desired end and ensure the zipper is in the closed position while installing. The back cover is a solid piece of polyethylene.
- Page 12 3. Disconnect the tube #5 from the connector #12 with a rubber mallet. Wrap the door panel around the tube. Slip the webbing strap between the tubes and then re-connect. Repeat for all the shoulders. Parts & Service: 020 8988 7400 / E-mail: Parts@clarkeinternational.com or Service@clarkeinternational.com...
- Page 13 4. Slip the webbing strap between tube #6 and the connector (as shown in Diagram J) and reconnect the tubes. 5. Repeat this step for the opposite shoulder. 6. Move to the apex of the garage using a step ladder and using a rubber mallet, disconnect the apex tube (#6) from the connector (#12).
- Page 14 5. Insert the hook on the ratchet into the hole on the bent corner leg. Wind the ratchet so that the webbing overlaps itself. 6. Slide the bottom cross rails through the fabric pockets at each leg and re-attach with clamps at each leg.
- Page 15 This can take the form of an additional Auger Securing Set GA1 (already supplied with Clarke instant garages), which can add greater security for exposed, windy locations. Alternatively the Easy Hook Anchoring System GHA2, can be used to provide greater security on soft ground.
Need help?
Do you have a question about the 3503578 and is the answer not in the manual?
Questions and answers