Table of Contents
Advertisement
E. Quick Programming Features
The K-1275 is programmed through the incoming phone line. The programming commands are structured so
that they do not interfere with the commands of a C-1000B controller
Description
Speed dial numbers ................................................................................................................. 0-46 digits**
Door strike time in sec (factory 05, 00 =.5 sec)*........................................................................ 2 digits
Door strike code (factory 6, no digits disables) ......................................................................... 1-2 digits
Maximum call time in min (factory 3, 0 = .5 min, no digits disables)* ...................................... 1 digit
Maximum ring time in sec (factory 20, 00 disables)* ............................................................... 2 digits
Silence Time Out in sec (factory 10, 00 disables)* ................................................................. 2 digits
Talk/listen delay time in .1 sec (factory 2)* .............................................................................. 1 digit
Security code (factory 845464)* ............................................................................................... 6 digits
Access code (factory set to 123456)* ....................................................................................... 1-6 digits
Keyless entry codes .................................................................................................................. 1-6 digits
Dial a (Q) .................................................................................................................................. #20
Dial a (#) ................................................................................................................................... #21
Add a 4 second pause ............................................................................................................. #22
Add a 1 second pause ............................................................................................................. #23
Second phone number selector ............................................................................................... #24
Normal dialing speed (factory setting) ..................................................................................... #30
Fast dialing speed ..................................................................................................................... #31
Hang up on dial tone enable (factory setting) .......................................................................... #32
Hang up on dial tone disable ................................................................................................... #33
Disable tenant initiated entry (factory setting) ........................................................................... #37
Enable tenant initiated entry ..................................................................................................... #38
Reset all programming to factory default settings ................................................................... ###
Hang up from programming ..................................................................................................... ##7
* Cannot contain "Q" or "#" (see #20 and #21)
Notes:
1. A single or double beep indicates a valid entry, three beeps indicate an error.
2. "Q" or "#", pauses or second phone number selector occupy one digit of memory.
F. Speed Dial Numbers
The K-1275 Entry Controller can be programmed with up to twelve 46 digit numbers. Each number can also be
programmed with special features such as pauses, and the Touch Tones "Q" and "#". Each of the special characters count
as a single digit. Each of the speed dial positions #01 to #12 pertain to the corresponding button on the front of the K-
1275. The button "0" uses position #10, the "Q" uses position #11 and the "#" uses position #12. To program a speed dial
position, enter programming (see section A) then enter the desired number followed by the selected position. To clear a
position, only enter a "#" followed by the position number with out any preceding number.
The K-1275 also has the capability to dial a second phone number if there is no answer or busy at the first number. This
can be used if the tenant wants the visitor to call their cell phone if they are not at home. To program a second number, be
sure that position #43 is programmed with the desired maximum ring time, then enter the first number to be dialed, followed
by "#24". A single beep should be heard. Next enter the second number to be dialed followed by "#" plus the memory
location. The total number of digits cannot exceed 46 for each position (45 digits if two numbers are programmed). The
following are examples of speed dial number entries:
To Program the K-1275 to...
...store 555-1234 at the first button position
...store a 9, a 1 second pause, then 333-4444 in the seventh button position
...store a 23Q# in the eight position
...store a first number of 22 and a second number of 33 in the "#"
button position
G. Door Strike Time
The actual time the door strike relay is energized is controlled by location #40. The time can be set from 00 to 99 seconds,
(an entry of "00" gives 0.5 seconds). In order to use this feature, be sure the relay door strike code is set (see section H).
H. Door Strike Code
A one or two digit door strike code can be entered by
programming position #41. When in programming, enter the
one or two digit code followed by "#41". Note: "Q" and "#"
can be entered as valid characters of the door strike code by
substituting "#20" and #21" (respectively) when programming
the door strike code (see section D). To disable the door
strike relay, enter "#41" without any preceding numbers.
Examples of door strike code entries are shown to the right.
** 45 digits maximum if two numbers are programmed in one memory location
To Program the
Door Strike Code to...
.
Enter Digits
Step 1 (see section A)
Enter programming
Enter programming
Enter programming
Enter programming
Step 1
(see section A)
"99"
Enter programming
"3"
Enter programming
Enter programming
"QQ"
"#1"
Enter programming
"Q"
Enter programming
+ Location
+
#01 - #12
+ #40
+ #41
+ #42
+ #43
+ #44
+ #45
+ #47
+ #48
+ #50 - #99
Step 2 - Enter Digits
5551234#01
9#233334444#07
23#20#21#08
22#24 (beep) 33#12
Step 2
Enter Digits
99#41
3#41
#20#20#41
#211#41
#20#41
9
Advertisement
Table of Contents
