Epson S1C63358 Technical Manual page 121

Register
Address
D3 D2
0 0
FFF2H
R
0 0
FFF3H
R
0 0
FFF4H
R
0 0
FFF5H
R
IT3 IT2
FFF6H
R/W
0 0
FFF7H
R
*1 Initial value at initial reset
*2 Not set in the circuit
*3 Constantly "0" when being read
KCP03–KCP00, KCP13–KCP10, KCP20: Input comparison registers (FF22H, FF26H, FF2AH•D0)
SIK03–SIK00, SIK13–SIK10, SIK20: Interrupt selection registers (FF20H, FF24H, FF28H•D0)
S1C63358 TECHNICAL MANUAL
CHAPTER 4: PERIPHERAL CIRCUITS AND OPERATION (Interrupt and HALT)
Table 4.15.4.1(b) Control bits of interrupt (2)
∗1
D1 D0 Name Init
∗3 ∗2
0 –
IPT1 IPT0
∗3 ∗2
0 –
IPT1 0
R/W
IPT0 0
∗3 ∗2
0 –
0 ISIF
∗3 ∗2
0 –
∗3 ∗2
0 –
R/W
ISIF 0
∗3 ∗2
0 –
0 IK0
∗3 ∗2
0 –
∗3 ∗2
0 –
R/W
IK0 0
∗3 ∗2
0
–
IK2 IK1
∗3 ∗2
0 –
IK2 0
R/W
IK1 0
IT3 0
IT1 IT0
IT2 0
IT1 0
IT0 0
∗3 ∗2
0 –
0 IAD
∗3 ∗2
0 –
∗3 ∗2
0 –
R/W
IAD 0
EIPT1, EIPT0: Interrupt mask registers (FFE2H•D1, D0)
IPT1, IPT0: Interrupt factor flags (FFF2H•D1, D0)
Refer to Section 4.11, "Programmable Timer".
EISIF: Interrupt mask register (FFE3H•D0)
ISIF: Interrupt factor flag (FFF3H•D0)
Refer to Section 4.12, "Serial Interface".
EIK0, EIK1, EIK2: Interrupt mask registers (FFE4H•D0, FFE5H•D0, FFE5H•D1)
IK0, IK1, IK2: Interrupt factor flags (FFF4H•D0, FFF5H•D0, FFF5H•D1)
Refer to Section 4.5, "Input Ports".
EIT3–EIT0: Interrupt mask registers (FFE6H)
IT3–IT0: Interrupt factor flags (FFF6H)
Refer to Section 4.9, "Clock Timer".
EIAD: Interrupt mask register (FFE7H•D0)
IAD: Interrupt factor flag (FFF7H•D0)
Refer to Section 4.10, "A/D Converter".
1 0
(R) (R)
Unused
Yes No Unused
(W) (W) Interrupt factor flag (Programmable timer 1)
Reset Invalid Interrupt factor flag (Programmable timer 0)
(R) (R) Unused
Yes No
Unused
(W) (W) Unused
Reset Invalid Interrupt factor flag (Serial I/F)
(R) (R) Unused
Yes No Unused
(W) (W)
Unused
Reset Invalid Interrupt factor flag (K00–K03)
(R) (R) Unused
Yes No Unused
(W) (W) Interrupt factor flag (K20)
Reset Invalid
Interrupt factor flag (K10–K13)
(R) (R) Interrupt factor flag (Clock timer 1 Hz)
Yes No
Interrupt factor flag (Clock timer 2 Hz)
(W) (W) Interrupt factor flag (Clock timer 8 Hz)
Reset Invalid Interrupt factor flag (Clock timer 16 Hz)
(R) (R) Unused
Yes No Unused
(W) (W)
Unused
Reset Invalid Interrupt factor flag (A/D converter)
EPSON
Comment
111