Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Saluki S1131
Summary of Contents for Saluki S1131
- Page 1 S1131 Signal Generator User Manual Saluki Technology Inc.
- Page 2 Tel: 886.2.2175 2930 Email: sales@salukitec.com www.salukitec.com The manual applies to the signal generator of the following models: S1131 Signal Generator (100kHz-3GHz). Standard Accessories of S1131 Signal Generator: Item Name Main Machine 1 Set Power Cord 1 pcs 1 pcs...
- Page 3 Manual rests with Saluki. Saluki Tech owns the copyright of this Manual which should not be modified or tampered by any organization or individual, or reproduced or transmitted for the purpose of making profit without its prior permission, otherwise Saluki will reserve the right to investigate and affix legal liability of infringement.
- Page 4 Tel: 886.2.2175 2930 Email: sales@salukitec.com www.salukitec.com Precautions "Warning" indicates danger. It reminds the user to pay attention to a certain operation process, operation method or similar situations. Noncompliance with the rules or improper operation may result in personal injuries. You must fully understand the warning and all the conditions in it shall be met before the next step "Attention"...
-
Page 5: Table Of Contents
Tel: 886.2.2175 2930 Email: sales@salukitec.com www.salukitec.com Content Overview ..................................7 1.1 Brief Introduction ..............................7 1.2 Key Feature ................................7 Safety Instructions ..............................8 2.1 Device safety ................................. 8 2.2 Precautions on personal safety..........................9 Brief Instruction ................................ 10 3.1 Unpacking ................................ - Page 6 Tel: 886.2.2175 2930 Email: sales@salukitec.com www.salukitec.com 6.2 FREQ ................................... 20 6.3 AMPTD ................................21 6.4 Sweep .................................. 22 6.6 Fctn ..................................24 6.7 Aux ..................................25...
-
Page 7: Overview
1.1 Brief Introduction S1131 is an economic signal generator for 3GHz span. It has good specification and multiple functions within a good looking small box. S1131 provide analog modulation and digital modulation as standard functions and is a good solution for RF R&D, test, maintenance and education. -
Page 8: Safety Instructions
Please read safety instruction carefully and Strictly follow！ Saluki spares no efforts to ensure that production process comply with latest safety standards so as to safeguard the safety of our users. The design and tests of our products and accessory equipment comply with relevant safety standards. We have established quality assurance system so that we can better supervise product quality and ensure that all products accord with standards in the system. -
Page 9: Precautions On Personal Safety
Tel: 886.2.2175 2930 Email: sales@salukitec.com www.salukitec.com 2.2 Precautions on personal safety. When moving the device, use proper tools and move the device softly so as to avoid personal injuries caused by the falling of the device. Device should be proper grounded so as to prevent personal injuries caused by poor or false grounding When cleaning the device, please unplug the device to avoid electric shock. -
Page 10: Brief Instruction
Inspect carefully whether the instrument has any damage during transportation. If the instrument has obvious damage, it is strictly forbidden to be powered on. Please contact Saluki and we will repair or exchange it be as soon as possible. 3.1.3 Operating Environment Refer to the part of environment adaptability in the technical specifications of appendix 1. -
Page 11: Electrostatic Protection
Tel: 886.2.2175 2930 Email: sales@salukitec.com www.salukitec.com Bad grounding or failure of the power supply may cause damage to the instrument, even personal injury. Before connecting the power supply of signal generator, make sure ground wires of the instrument and its power supply are in good contact. Use a power socket with protective grounding and do not substitute the protective ground wire with an external cable. -
Page 12: Routine Maintenance
Tel: 886.2.2175 2930 Email: sales@salukitec.com www.salukitec.com 3.2 Routine Maintenance It is required to check and clean the instrument after a period of use. Please proceed as the following procedures: Shut down. Unplug the power cord. Use a clean and soft cloth with detergent to wipe the keys gently. Wipe up the display with a clean and soft cloth. -
Page 13: Front And Rear Panels
Frequency settings. Include CW frequency, frequency reference, frequency offset AMPTD Amplitude Settings. Include ALC settings, reference amplitude, amplitude deviations and cable loss compensation. Sweep settings. S1131 supports frequency sweep, power sweep, frequency + Power sweep. List sweep and step Sweep sweep are supported. -
Page 14: Output Function Switch Keys
Tel: 886.2.2175 2930 Email: sales@salukitec.com www.salukitec.com 4.1.2.1 Knob and navigation keys Knob functions: When entering numbers, step up (clockwise) or down (anticlockwise) the instrument parameters as specified; To move the selection bar in the focus area (such as list) ... -
Page 15: Front Panel Interfaces
4.1.4.3 LF Out LF Out port is a 50ohm SMA port. It is used to output low frequency signals in different waveform. 4.1.4.4 RF Out RF Out port is a 50ohm N type port. It is the main output port of S1131. -
Page 16: Rear Panel
Tel: 886.2.2175 2930 Email: sales@salukitec.com www.salukitec.com 4.2 Rear Panel Figure 4-2 S1131 Signal Generator Rear Panel Description Description AC power plug Power switch USB port 10M Reference Input LAN port External Trigger Input RS232 port 4.3 UI... - Page 17 Tel: 886.2.2175 2930 Email: sales@salukitec.com www.salukitec.com Figure 4-3 S1131 Signal Generator UI Main configuration display Setting input bar Detail setting display Soft menu...
-
Page 18: Typical Operation
Press the power button to turn on S1131 signal generator. This chapter means to show the basic operations of S1131 Signal Generator. Spectrum analyzer is used to simulate the receiver. In this menu, S3331B spectrum analyzer is used for signal analysis. For operation of S3331B please refer to document S3331- 03-02 ( S3331 series spectrum analyzer user manual). -
Page 19: Step Sweep Output
S1131 supports step sweep function. Step sweep is supported by frequency, amplitude and frequency+amplitude. Following example will show how to set S1131 to enable the step sweep in frequency + amplitude mode. Connect S1131 to S3331 via a N type cable Preset the S1131, S3331 Press【PRESET】... -
Page 20: List Sweep Output
Tel: 886.2.2175 2930 Email: sales@salukitec.com www.salukitec.com 5.4 List Sweep Output S1131 supports list sweep function. User can edit the point freely and create a sweep list. This example creates a 4 point sweep list. Connect S1131 to S3331 via a N type cable Preset the S1131, S3331 Press【PRESET】... -
Page 21: Analog Modulation Signal
11) Set the S3331 accordingly. Please see following screenshot 5.5 Analog Modulation Signal S1131 supports analog modulation as a standard function, AM, FM, PM, Pulse modulation are supported. This example will show how to set an AM output signal. Connect S1131 to S3331 via a N type cable Preset the S1131, S3331 Press【PRESET】... -
Page 22: Digital Demodulation Signal
Press 【RF】to enable the output. Press【MOD】key to enable modulation function. 10) Set the S3331 accordingly (AM demodulation function). Please see following screenshot 5.6 Digital Demodulation Signal S1131 supports digital modulation as a standard function, following modulations are supported 2ASK ... -
Page 23: Lf Output
Press 【RF】to enable the output. Press【MOD】key to enable modulation function. 5.7 LF Output S1131 support internal modulation source output. Sine, square, triangle and saw tooth waveforms are supported. This example will show how to set a Triangle wave output. Preset the S1131 Press【PRESET】... -
Page 24: Menu Description
This chapter will provide a full function – menu mapping and will give description of each menu option. 6.1 Menu Structure This section provides the structure of all buttons and soft-keys. S1131 has following function keys on front panel. Following paragraphs will show the menu structure of these keys. FREQ ... -
Page 25: Freq
Tel: 886.2.2175 2930 Email: sales@salukitec.com www.salukitec.com 6.2 FREQ The 【FREQ】 key on the front panel is used to set parameters related to the signal generator frequency, including [Ref Set], [Ref State], [Offset], [Multiplier], [10MHzRef]. Following diagram gives a direct view of the menu structure [Ref Set] ... -
Page 26: Amptd
Tel: 886.2.2175 2930 Email: sales@salukitec.com www.salukitec.com 6.3 AMPTD Pop up menus related to parameter setting of Amplitude, including [ALC], [Response], [Ref Set], [Ref State], [Offset] and [I.L Cable]. Please refer to following diagram for the menu structure. [ALC] Menu description: to turn on/off the ALC function, ALC function provides a more stable output. [Response] ... -
Page 27: Sweep
Tel: 886.2.2175 2930 Email: sales@salukitec.com www.salukitec.com 6.4 Sweep [Sweep Mode] Menu description: Select sweep mode between [Freq], [AMPL] and [Freq & Ampl]. [Sweep Type] ... - Page 28 Menu description: switch between single sweep and continuous sweep. [Single Sweep] Menu description: when [Single] is selected in [Sweep Repe], [Single Sweep] acts as a trigger. S1131 sweeps each time when [Single Sweep] is clicked. [CFG Step] ...
-
Page 29: Fctn
Tel: 886.2.2175 2930 Email: sales@salukitec.com www.salukitec.com 6.6 Fctn [Analog] Menu description: Analog modulation functions, [AM], [FM] and [фM] are supported. [AM] Menu description: Amplitude modulation function, user can set [Depth] and [Rate] in submenu. Carrier wave output is configured in 【FREQ】... -
Page 30: Aux
Menu description: S1131 support ASK, FSK, PSK modulation. 2ASK is supported, user can configure [ASK Deep] and [Rate] in submenu. 2FSK, 4FSK, 8FSK are supported, user can configure [FSK Offset] and [Rate]. 2PSK, 4PSK and 8PSK are supported, user can set [Deviation] and [Rate]. - Page 31 Tel: 886.2.2175 2930 Email: sales@salukitec.com www.salukitec.com [LAN] Menu description: to set the IP address for the instrument...