Advertisement
Quick Links
AB-6a Cupboard & Pull Out Drawer/Table Assembly Instructions
Note: If you have two of the same cabinet each cabinet will have a different cabinet number. Prior
to assembly, separate and group all matching panels panel numbers.
Panel Stickers/Labels –Do not remove any cabinet stickers from the panels until the
units have been built, as these will assist with assembly. Most of the stickers are
placed on the "back" or underside of the cabinet and will not be seen once assembled.
AB-6a Cupboard & Drawer Panels
Cupboard Door
End Right
End Left
Top Panel
Back
Bottom Panel
Pull Out Drawer/Table Front
Adjustable Shelf
Pull Out Drawer/Table Bottom
Kick
1
©2019 WallBeds Australia
Advertisement
Subscribe to Our Youtube Channel
Related Manuals for Wallbeds Australia AB-6a
Summary of Contents for Wallbeds Australia AB-6a
- Page 1 AB-6a Cupboard & Pull Out Drawer/Table Assembly Instructions Note: If you have two of the same cabinet each cabinet will have a different cabinet number. Prior to assembly, separate and group all matching panels panel numbers. Panel Stickers/Labels –Do not remove any cabinet stickers from the panels until the units have been built, as these will assist with assembly.
- Page 2 AB-6a Cupboard Drawer Hardware Parts Small Handle Drawer Clip Pullout Drawer/Table Runners Handle Screw Door Hinge Door Hinge Clip Euro Screw Cam Lock Cam Pin Adjustable Shelf Pin Dome Head Screw 28mm Wood Screw Step 1 – Inserting Hardware Cam Locks – Insert all Cam Locks into the following panels as described by the cabinet part located on the cabinet sticker.
- Page 3 Insert these into the drawer front ensuring the up & down arrows on the drawer clips are facing the outside edge of the drawer panel. Refer image 10 page 11 Fix these into the drawer front by tapping them in gently with a hammer. ©2019 WallBeds Australia...
- Page 4 Cupboard Door - Line up the prongs on the door hinge with the hinge clips. Push the door, so these clips are all the way in and then push the back of the hinge arm until you hear it click into position. Refer image 8 page 10 ©2019 WallBeds Australia...
- Page 5 AB-6a Top Cabinet Assembly Instructions Note: If you have two of the same cabinet each cabinet will have a different cabinet number. Prior to assembly, separate and group all matching panels panel numbers. Panel Stickers/Labels –Do not remove any cabinet stickers from the panels until the units have been built, as these will assist with assembly.
- Page 6 AB-6a Top Cabinet Hardware Parts Cam Lock Small Handle Cam Pin Handle Fixing Screw Shelf Pin Door Hinge Clip Door Hinge 28mm Wood Screw Step 1 – Inserting Hardware Cam Locks – Insert all Cam Locks into the following panels as described by the cabinet part located on the cabinet sticker.
-
Page 7: Step 2 - Cabinet Assembly
• Using an existing shelf pin hole, pre-drill a 5mm hole through the end panel but no-more than 5mm into the End Panel of the wall bed. Fix the cabinet to the side of the wall bed cabinet by using the 28mm wood screws supplied. ©2019 WallBeds Australia... -
Page 8: Important Safety Information
Phillips head screw driver. IMPORTANT SAFETY INFORMATION All WallBeds Australia Bookcases and Cabinets must be securely attached to the WallBed before use. Ensure that children DO NOT climb or hang on any part of the Bookcase or Cabinet. - Page 9 Image 1 Image 2 Image 3 Image 4 Image 5 ©2019 WallBeds Australia...
- Page 10 Image 7 Image 6 Image 8 Image 9 ©2019 WallBeds Australia...
- Page 11 Image 10 Image 11 Image 12 NOTE: Image s 11 & 12 is a representation of how to place the Top unit onto Lower unit. These images may not represent the product purchased. ©2019 WallBeds Australia...
Need help?
Do you have a question about the AB-6a and is the answer not in the manual?
Questions and answers